HDMI 显示器停止工作

HDMI 显示器停止工作

它曾经工作过,但突然停止工作。(显示器无显示,显示器电源指示灯一直闪烁)

系统日志:(如果我需要添加更多内容请告诉我)

(每个命令都是在 HDMI 电缆连接到笔记本电脑(Dell Inspiron 14 7000)和显示器(Acer)时运行的


# uname -r

4.8.0-58-generic

# lshw -c video

  *-display               
       description: VGA compatible controller
       product: Intel Corporation
       vendor: Intel Corporation
       physical id: 2
       bus info: pci@0000:00:02.0
       version: 02
       width: 64 bits
       clock: 33MHz
       capabilities: pciexpress msi pm vga_controller bus_master cap_list rom
       configuration: driver=i915 latency=0
       resources: irq:280 memory:d4000000-d4ffffff memory:b0000000-bfffffff ioport:f000(size=64) memory:c0000-dffff
  *-display
       description: 3D controller
       product: GM108M [GeForce 940MX]
       vendor: NVIDIA Corporation
       physical id: 0
       bus info: pci@0000:01:00.0
       version: a2
       width: 64 bits
       clock: 33MHz
       capabilities: pm msi pciexpress bus_master cap_list rom
       configuration: driver=nvidia latency=0
       resources: irq:284 memory:d2000000-d2ffffff memory:c0000000-cfffffff memory:d0000000-d1ffffff ioport:e000(size=128) memory:d3000000-d307ffff

get-edid | parse-edid

This is read-edid version 3.0.2. Prepare for some fun.
Attempting to use i2c interface
No EDID on bus 0
No EDID on bus 2
No EDID on bus 4
No EDID on bus 5
No EDID on bus 6
2 potential busses found: 1 3
Will scan through until the first EDID is found.
Pass a bus number as an option to this program to go only for that one.
256-byte EDID successfully retrieved from i2c bus 1
Looks like i2c was successful. Have a good day.
Checksum Correct

Section "Monitor"
        Identifier "R231"
        ModelName "R231"
        VendorName "ACR"
        # Monitor Manufactured week 36 of 2016
        # EDID version 1.3
        # Digital Display
        DisplaySize 510 290
        Gamma 2.20
        Option "DPMS" "true"
        Horizsync 31-75
        VertRefresh 56-75
        # Maximum pixel clock is 180MHz
        #Not giving standard mode: 1152x864, 75Hz
        #Not giving standard mode: 1280x1024, 60Hz
        #Not giving standard mode: 1280x720, 60Hz
        #Not giving standard mode: 1280x800, 60Hz
        #Not giving standard mode: 1440x900, 60Hz
        #Not giving standard mode: 1680x1050, 60Hz
        #Not giving standard mode: 1920x1080, 60Hz

        #Extension block found. Parsing...
        Modeline        "Mode 10" 148.50 1920 2008 2052 2200 1080 1084 1089 1125 +hsync +vsync 
        Modeline        "Mode 0" 148.50 1920 2008 2052 2200 1080 1084 1089 1125 +hsync +vsync 
        Modeline        "Mode 1" 148.500 1920 2008 2052 2200 1080 1084 1089 1125 +hsync +vsync
        Modeline        "Mode 2" 25.200 640 656 752 800 480 490 492 525 -hsync -vsync
        Modeline        "Mode 3" 27.027 720 736 798 858 480 489 495 525 -hsync -vsync
        Modeline        "Mode 4" 74.250 1280 1390 1420 1650 720 725 730 750 +hsync +vsync
        Modeline        "Mode 5" 27.000 720 732 796 864 576 581 586 625 -hsync -vsync
        Modeline        "Mode 6" 74.250 1280 1720 1760 1980 720 725 730 750 +hsync +vsync
        Modeline        "Mode 7" 148.500 1920 2448 2492 2640 1080 1084 1089 1125 +hsync +vsync
        Modeline        "Mode 8" 74.250 1920 2008 2052 2200 1080 1082 1087 1125 +hsync +vsync interlace
        Modeline        "Mode 9" 74.250 1920 2448 2492 2640 1080 1082 1089 1125 +hsync +vsync interlace
        Modeline        "Mode 11" 74.25 1280 1390 1430 1650 720 725 730 750 +hsync +vsync 
        Modeline        "Mode 12" 27.00 720 736 798 858 480 489 495 525 -hsync -vsync 
        Modeline        "Mode 13" 25.18 640 648 744 800 480 482 484 525 -hsync -vsync 
        Option "PreferredMode" "Mode 10"
EndSection

dmesg | grep microcode

[    1.112196] microcode: sig=0x806e9, pf=0x80, revision=0x42
[    1.112258] microcode: Microcode Update Driver: v2.01 <[email protected]>, Peter Oruba

cat /etc/X11/xorg.conf

Section "ServerLayout"
    Identifier "layout"
    Screen 0 "nvidia"
    Inactive "intel"
EndSection

Section "Device"
    Identifier "intel"
    Driver "modesetting"
    BusID "PCI:0@0:2:0"
    Option "AccelMethod" "None"
EndSection

Section "Screen"
    Identifier "intel"
    Device "intel"
EndSection

Section "Device"
    Identifier "nvidia"
    Driver "nvidia"
    BusID "PCI:1@0:0:0"
    Option "ConstrainCursor" "off"
EndSection

Section "Screen"
    Identifier "nvidia"
    Device "nvidia"
    Option "AllowEmptyInitialConfiguration" "on"
    Option "IgnoreDisplayDevices" "CRT"
EndSection

# xrandr

eDP-1-1 connected primary 1920x1080+0+0 309mm x 174mm
   1920x1080     60.02*+  59.93    48.03  
   1680x1050     59.95    59.88  
   1600x1024     60.17  
   1400x1050     59.98  
   1280x1024     60.02  
   1440x900      59.89  
   1280x960      60.00  
   1360x768      59.80    59.96  
   1152x864      60.00  
   1024x768      60.04    60.00  
   960x720       60.00  
   928x696       60.05  
   896x672       60.01  
   960x600       60.00  
   960x540       59.99  
   800x600       60.00    60.32    56.25  
   840x525       60.01    59.88  
   800x512       60.17  
   700x525       59.98  
   640x512       60.02  
   720x450       59.89  
   640x480       60.00    59.94  
   680x384       59.80    59.96  
   576x432       60.06  
   512x384       60.00  
   400x300       60.32    56.34  
   320x240       60.05  
DP-1-1 disconnected

答案1

这很有趣,也难以解释,但我所做的就是解决这个问题

  • 使用 cvt 创建模式行字符串$ cvt 1920 1080(我知道显示器的分辨率)
  • 编辑xorg.conf并强制 Modeline 并告诉它忽略显示器发送的 EDID 信息。(https://wiki.ubuntu.com/X/Config/HDMI

这些步骤在我重新启动时破坏了我的系统,它进入了某种安全模式,我可以在其中编辑我的 xorg.conf。这也使外部显示器上的显示恢复正常。在对 xorg.conf 进行一些调整后,我能够正确配置,重新引导到正常模式,并用我备份的原始配置替换修改后的配置,一切正常。

相关内容