我正在运行 Cirrus 7 和 Ubuntu 17.10，不幸的是，它配备了 Centrino Advanced-N 6235。这个无线适配器工作得不太好，反应时间很慢，我无法获得超过 600 KB/S 的吞吐量，而同一网络上的其他设备可以轻松达到 5 MB/s。我找到了几篇解决此问题的帖子：
Intel Centrino Centrino Advanced-N 6235 无线信号弱
Lubuntu 13.10 Intel Corporation Centrino Advanced-N 6235 (rev-24) 问题
Intel Centrino Advanced-N 6235 吞吐量
但是它们已经很旧了，而且大多指的是旧的内核错误，该错误似乎在几年前就已修复： https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1159145
所以我想知道是否有人可以毫无问题地运行此无线适配器。这是硬件问题还是软件问题？我可以做些什么来改善连接？
以下是 dsmg 输出的示例（我更改了 MAC 地址）：
sudo dmesg | grep wlan0
[233696.907293] wlan0: associate with e0:28:6d:30:13:4c (try 1/3)
[233696.943294] wlan0: associate with e0:28:6d:30:13:4c (try 2/3)
[233696.950553] wlan0: RX AssocResp from e0:28:6d:30:13:4c (capab=0x1431 status=0 aid=3)
[233696.971412] wlan0: associated
[233697.148133] wlan0: Limiting TX power to 20 (20 - 0) dBm as advertised by e0:28:6d:30:13:4c
[234303.411322] wlan0: deauthenticated from e0:28:6d:30:13:4c (Reason: 2=PREV_AUTH_NOT_VALID)
[234306.669023] wlan0: authenticate with XX:28:6d:30:13:XX
[234306.671710] wlan0: send auth to XX:28:6d:30:13:XX (try 1/3)
[234306.740030] wlan0: send auth to XX:28:6d:30:13:XX (try 2/3)
[234306.741659] wlan0: authenticated
[234306.743528] wlan0: associate with XX:28:6d:30:13:XX (try 1/3)
[234306.754636] wlan0: associate with XX:28:6d:30:13:XX (try 2/3)
[234306.762087] wlan0: RX AssocResp from XX:28:6d:30:13:XX (capab=0x1511 status=0 aid=1)
[234306.781035] wlan0: associated
[234306.833064] wlan0: Limiting TX power to 20 (23 - 3) dBm as advertised by XX:28:6d:30:13:XX
[234963.247556] wlan0: deauthenticating from XX:28:6d:30:13:XX by local choice (Reason: 3=DEAUTH_LEAVING)
[234977.040692] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[234977.446692] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[234977.742178] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[234983.631079] wlan0: authenticate with XX:28:6d:30:13:XX
[234983.633661] wlan0: send auth to XX:28:6d:30:13:XX (try 1/3)
[234983.647935] wlan0: send auth to XX:28:6d:30:13:XX (try 2/3)
[234983.649515] wlan0: authenticated
[234983.651185] wlan0: associate with XX:28:6d:30:13:XX (try 1/3)
[234983.662128] wlan0: associate with XX:28:6d:30:13:XX (try 2/3)
[234983.663729] wlan0: RX AssocResp from XX:28:6d:30:13:XX (capab=0x1511 status=0 aid=1)
[234983.681553] wlan0: associated
[234983.681642] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[234983.741230] wlan0: Limiting TX power to 27 (30 - 3) dBm as advertised by XX:28:6d:30:13:XX
[236621.605584] wlan0: authenticate with e0:28:6d:30:13:4c
[236621.608725] wlan0: send auth to e0:28:6d:30:13:4c (try 1/3)
[236621.631390] wlan0: send auth to e0:28:6d:30:13:4c (try 2/3)
[236621.634509] wlan0: authenticated
[236621.636467] wlan0: associate with e0:28:6d:30:13:4c (try 1/3)
[236621.672118] wlan0: associate with e0:28:6d:30:13:4c (try 2/3)
[236621.677269] wlan0: RX AssocResp from e0:28:6d:30:13:4c (capab=0x1431 status=0 aid=2)
[236621.697238] wlan0: associated
[236622.018362] wlan0: Limiting TX power to 20 (20 - 0) dBm as advertised by e0:28:6d:30:13:4c
[236631.185506] wlan0: deauthenticated from e0:28:6d:30:13:4c (Reason: 2=PREV_AUTH_NOT_VALID)
[236634.316592] wlan0: authenticate with XX:28:6d:30:13:XX
[236634.319552] wlan0: send auth to XX:28:6d:30:13:XX (try 1/3)
[236634.436946] wlan0: send auth to XX:28:6d:30:13:XX (try 2/3)
[236634.446272] wlan0: send auth to XX:28:6d:30:13:XX (try 3/3)
[236634.447530] wlan0: authenticated
[236634.448951] wlan0: associate with XX:28:6d:30:13:XX (try 1/3)
[236634.461017] wlan0: associate with XX:28:6d:30:13:XX (try 2/3)
[236634.462678] wlan0: RX AssocResp from XX:28:6d:30:13:XX (capab=0x1511 status=0 aid=1)
[236634.480750] wlan0: associated
[236634.539934] wlan0: Limiting TX power to 27 (30 - 3) dBm as advertised by XX:28:6d:30:13:XX
[237344.790317] wlan0: authenticate with XX:28:6d:30:13:XX
[237344.792735] wlan0: send auth to XX:28:6d:30:13:XX (try 1/3)
[237344.805029] wlan0: send auth to XX:28:6d:30:13:XX (try 2/3)
[237344.908714] wlan0: send auth to XX:28:6d:30:13:XX (try 3/3)
[237344.916829] wlan0: authentication with XX:28:6d:30:13:XX timed out
[237348.565955] wlan0: authenticate with e0:28:6d:30:13:4c
[237348.571036] wlan0: send auth to e0:28:6d:30:13:4c (try 1/3)
[237348.573630] wlan0: authenticated
[237348.576910] wlan0: associate with e0:28:6d:30:13:4c (try 1/3)
[237348.611628] wlan0: associate with e0:28:6d:30:13:4c (try 2/3)
[237348.616068] wlan0: RX AssocResp from e0:28:6d:30:13:4c (capab=0x1431 status=0 aid=2)
[237348.636020] wlan0: associated
[237348.646800] wlan0: Limiting TX power to 20 (20 - 0) dBm as advertised by e0:28:6d:30:13:4c
[237355.786883] wlan0: deauthenticated from e0:28:6d:30:13:4c (Reason: 2=PREV_AUTH_NOT_VALID)
[237359.024330] wlan0: authenticate with XX:28:6d:30:13:XX
[237359.027513] wlan0: send auth to XX:28:6d:30:13:XX (try 1/3)
[237359.037446] wlan0: send auth to XX:28:6d:30:13:XX (try 2/3)
[237359.038615] wlan0: authenticated
[237359.040669] wlan0: associate with XX:28:6d:30:13:XX (try 1/3)
[237359.052525] wlan0: associate with XX:28:6d:30:13:XX (try 2/3)
[237359.054652] wlan0: RX AssocResp from XX:28:6d:30:13:XX (capab=0x1511 status=0 aid=1)
[237359.072555] wlan0: associated
[237359.132027] wlan0: Limiting TX power to 27 (30 - 3) dBm as advertised by XX:28:6d:30:13:XX
[237739.358617] wlan0: deauthenticating from XX:28:6d:30:13:XX by local choice (Reason: 3=DEAUTH_LEAVING)
[237753.219112] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[237753.624920] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[237753.888248] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[237759.917539] wlan0: authenticate with XX:28:6d:30:13:XX
[237759.920045] wlan0: send auth to XX:28:6d:30:13:XX (try 1/3)
[237759.938618] wlan0: authenticated
[237759.940713] wlan0: associate with XX:28:6d:30:13:XX (try 1/3)
[237759.951878] wlan0: associate with XX:28:6d:30:13:XX (try 2/3)
[237759.959327] wlan0: RX AssocResp from XX:28:6d:30:13:XX (capab=0x1511 status=0 aid=1)
[237759.977302] wlan0: associated
[237759.977369] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[237760.039421] wlan0: Limiting TX power to 27 (30 - 3) dBm as advertised by XX:28:6d:30:13:XX
[255142.566147] wlan0: deauthenticating from XX:28:6d:30:13:XX by local choice (Reason: 3=DEAUTH_LEAVING)
[255155.687210] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[255156.085066] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[255156.181962] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[255162.095411] wlan0: authenticate with XX:28:6d:30:13:XX
[255162.097742] wlan0: send auth to XX:28:6d:30:13:XX (try 1/3)
[255162.124284] wlan0: send auth to XX:28:6d:30:13:XX (try 2/3)
[255162.125497] wlan0: authenticated
[255162.126288] wlan0: associate with XX:28:6d:30:13:XX (try 1/3)
[255162.138552] wlan0: associate with XX:28:6d:30:13:XX (try 2/3)
[255162.145925] wlan0: RX AssocResp from XX:28:6d:30:13:XX (capab=0x1511 status=0 aid=1)
[255162.163629] wlan0: associated
[255162.163681] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[255162.217334] wlan0: Limiting TX power to 27 (30 - 3) dBm as advertised by XX:28:6d:30:13:XX
[265911.077667] wlan0: deauthenticating from XX:28:6d:30:13:XX by local choice (Reason: 3=DEAUTH_LEAVING)
[265923.912257] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[265924.314049] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[265924.371327] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[265930.268754] wlan0: authenticate with XX:28:6d:30:13:XX
[265930.271147] wlan0: send auth to XX:28:6d:30:13:XX (try 1/3)
[265930.284924] wlan0: send auth to XX:28:6d:30:13:XX (try 2/3)
[265930.286114] wlan0: authenticated
[265930.286534] wlan0: associate with XX:28:6d:30:13:XX (try 1/3)
[265930.299044] wlan0: associate with XX:28:6d:30:13:XX (try 2/3)
[265930.306503] wlan0: RX AssocResp from XX:28:6d:30:13:XX (capab=0x1511 status=0 aid=1)
[265930.324717] wlan0: associated
[265930.325206] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[265930.378405] wlan0: Limiting TX power to 27 (30 - 3) dBm as advertised by XX:28:6d:30:13:XX
[271013.727836] wlan0: deauthenticating from XX:28:6d:30:13:XX by local choice (Reason: 3=DEAUTH_LEAVING)
[271026.951951] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[271027.357950] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[271027.410915] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[271033.366098] wlan0: authenticate with XX:28:6d:30:13:XX
[271033.368730] wlan0: send auth to XX:28:6d:30:13:XX (try 1/3)
[271033.395844] wlan0: authenticated
[271033.398253] wlan0: associate with XX:28:6d:30:13:XX (try 1/3)
[271033.409441] wlan0: associate with XX:28:6d:30:13:XX (try 2/3)
[271033.416957] wlan0: RX AssocResp from XX:28:6d:30:13:XX (capab=0x1511 status=0 aid=1)
[271033.434932] wlan0: associated
[271033.435004] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[271033.497089] wlan0: Limiting TX power to 20 (23 - 3) dBm as advertised by XX:28:6d:30:13:XX
[272762.239176] wlan0: deauthenticating from XX:28:6d:30:13:XX by local choice (Reason: 3=DEAUTH_LEAVING)
[272775.666048] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[272776.067294] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[272776.117239] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[272838.239374] wlan0: authenticate with XX:28:6d:30:13:XX
[272838.241560] wlan0: send auth to XX:28:6d:30:13:XX (try 1/3)
[272838.272957] wlan0: send auth to XX:28:6d:30:13:XX (try 2/3)
[272838.275026] wlan0: authenticated
[272838.277163] wlan0: associate with XX:28:6d:30:13:XX (try 1/3)
[272838.289537] wlan0: associate with XX:28:6d:30:13:XX (try 2/3)
[272838.298572] wlan0: associate with XX:28:6d:30:13:XX (try 3/3)
[272838.309708] wlan0: association with XX:28:6d:30:13:XX timed out
[272841.443464] wlan0: authenticate with XX:28:6d:30:13:XX
[272841.445794] wlan0: send auth to XX:28:6d:30:13:XX (try 1/3)
[272841.973571] wlan0: send auth to XX:28:6d:30:13:XX (try 2/3)
[272842.997646] wlan0: send auth to XX:28:6d:30:13:XX (try 3/3)
[272843.989754] wlan0: authentication with XX:28:6d:30:13:XX timed out
[272847.703152] wlan0: authenticate with XX:28:6d:30:13:XX
[272847.705736] wlan0: send auth to XX:28:6d:30:13:XX (try 1/3)
[272847.796103] wlan0: send auth to XX:28:6d:30:13:XX (try 2/3)
[272847.798085] wlan0: authenticated
[272847.802088] wlan0: associate with XX:28:6d:30:13:XX (try 1/3)
[272847.813819] wlan0: associate with XX:28:6d:30:13:XX (try 2/3)
[272847.821237] wlan0: RX AssocResp from XX:28:6d:30:13:XX (capab=0x1511 status=0 aid=1)
[272847.839254] wlan0: associated
[272847.839329] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[272847.890330] wlan0: Limiting TX power to 20 (23 - 3) dBm as advertised by XX:28:6d:30:13:XX
[274485.409701] wlan0: deauthenticating from XX:28:6d:30:13:XX by local choice (Reason: 3=DEAUTH_LEAVING)
[274499.016437] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[274499.418745] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[274499.489509] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[274505.623403] wlan0: authenticate with XX:28:6d:30:13:XX
[274505.625906] wlan0: send auth to XX:28:6d:30:13:XX (try 1/3)
[274505.717769] wlan0: send auth to XX:28:6d:30:13:XX (try 2/3)
[274505.719480] wlan0: authenticated
[274505.722457] wlan0: associate with XX:28:6d:30:13:XX (try 1/3)
[274505.734346] wlan0: associate with XX:28:6d:30:13:XX (try 2/3)
[274505.741845] wlan0: RX AssocResp from XX:28:6d:30:13:XX (capab=0x1511 status=0 aid=1)
[274505.760225] wlan0: associated
[274505.760296] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[274505.812735] wlan0: Limiting TX power to 20 (23 - 3) dBm as advertised by XX:28:6d:30:13:XX
[276263.823953] wlan0: disconnect from AP XX:28:6d:30:13:XX for new auth to e0:28:6d:30:13:4c
[276263.864757] wlan0: authenticate with e0:28:6d:30:13:4c
[276263.869263] wlan0: send auth to e0:28:6d:30:13:4c (try 1/3)
[276263.894125] wlan0: send auth to e0:28:6d:30:13:4c (try 2/3)
[276263.897166] wlan0: authenticated
[276263.897559] wlan0: associate with e0:28:6d:30:13:4c (try 1/3)
[276263.939189] wlan0: associate with e0:28:6d:30:13:4c (try 2/3)
[276263.943740] wlan0: RX AssocResp from e0:28:6d:30:13:4c (capab=0x1431 status=0 aid=2)
[276263.965093] wlan0: associated
[276263.992147] wlan0: Limiting TX power to 20 (20 - 0) dBm as advertised by e0:28:6d:30:13:4c
[276624.641168] wlan0: disconnect from AP e0:28:6d:30:13:4c for new auth to XX:28:6d:30:13:XX
[276624.679870] wlan0: authenticate with XX:28:6d:30:13:XX
[276624.682694] wlan0: send auth to XX:28:6d:30:13:XX (try 1/3)
[276624.801930] wlan0: send auth to XX:28:6d:30:13:XX (try 2/3)
[276624.810914] wlan0: send auth to XX:28:6d:30:13:XX (try 3/3)
[276624.818445] wlan0: authentication with XX:28:6d:30:13:XX timed out
[276624.982863] wlan0: authenticate with e0:28:6d:30:13:4c
[276624.994506] wlan0: send auth to e0:28:6d:30:13:4c (try 1/3)
[276625.108991] wlan0: send auth to e0:28:6d:30:13:4c (try 2/3)
[276625.131145] wlan0: send auth to e0:28:6d:30:13:4c (try 3/3)
[276625.138901] wlan0: authenticated
[276625.141010] wlan0: associate with e0:28:6d:30:13:4c (try 1/3)
[276625.178807] wlan0: associate with e0:28:6d:30:13:4c (try 2/3)
[276625.183263] wlan0: RX AssocResp from e0:28:6d:30:13:4c (capab=0x1431 status=0 aid=2)
[276625.203002] wlan0: associated
[276625.257311] wlan0: Limiting TX power to 20 (20 - 0) dBm as advertised by e0:28:6d:30:13:4c
[276635.871049] wlan0: deauthenticated from e0:28:6d:30:13:4c (Reason: 2=PREV_AUTH_NOT_VALID)
[276639.031276] wlan0: authenticate with XX:28:6d:30:13:XX
[276639.033974] wlan0: send auth to XX:28:6d:30:13:XX (try 1/3)
[276639.138661] wlan0: send auth to XX:28:6d:30:13:XX (try 2/3)
[276639.147762] wlan0: send auth to XX:28:6d:30:13:XX (try 3/3)
[276639.156383] wlan0: authentication with XX:28:6d:30:13:XX timed out
[276640.216800] wlan0: authenticate with e0:28:6d:30:13:4c
[276640.219983] wlan0: send auth to e0:28:6d:30:13:4c (try 1/3)
[276640.239414] wlan0: send auth to e0:28:6d:30:13:4c (try 2/3)
[276640.242444] wlan0: authenticated
[276640.245338] wlan0: associate with e0:28:6d:30:13:4c (try 1/3)
[276640.279651] wlan0: associate with e0:28:6d:30:13:4c (try 2/3)
[276640.284378] wlan0: RX AssocResp from e0:28:6d:30:13:4c (capab=0x1431 status=0 aid=2)
[276640.304424] wlan0: associated
[276640.412464] wlan0: Limiting TX power to 20 (20 - 0) dBm as advertised by e0:28:6d:30:13:4c
[277192.251810] wlan0: deauthenticating from e0:28:6d:30:13:4c by local choice (Reason: 3=DEAUTH_LEAVING)
[277205.451169] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[277205.861206] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[277205.927044] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[277211.877521] wlan0: authenticate with XX:28:6d:30:13:XX
[277211.880213] wlan0: send auth to XX:28:6d:30:13:XX (try 1/3)
[277211.954629] wlan0: authenticated
[277211.957132] wlan0: associate with XX:28:6d:30:13:XX (try 1/3)
[277211.968471] wlan0: associate with XX:28:6d:30:13:XX (try 2/3)
[277211.975972] wlan0: RX AssocResp from XX:28:6d:30:13:XX (capab=0x1511 status=0 aid=1)
[277211.994133] wlan0: associated
[277211.994208] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[277212.055356] wlan0: Limiting TX power to 20 (23 - 3) dBm as advertised by XX:28:6d:30:13:XX
[278405.085021] wlan0: deauthenticating from XX:28:6d:30:13:XX by local choice (Reason: 3=DEAUTH_LEAVING)
[278418.475479] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[278418.877821] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[278418.944418] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[278424.847326] wlan0: authenticate with XX:28:6d:30:13:XX
[278424.849750] wlan0: send auth to XX:28:6d:30:13:XX (try 1/3)
[278424.932183] wlan0: send auth to XX:28:6d:30:13:XX (try 2/3)
[278424.933381] wlan0: authenticated
[278424.935313] wlan0: associate with XX:28:6d:30:13:XX (try 1/3)
[278424.947366] wlan0: associate with XX:28:6d:30:13:XX (try 2/3)
[278424.948981] wlan0: RX AssocResp from XX:28:6d:30:13:XX (capab=0x1511 status=0 aid=2)
[278424.967788] wlan0: associated
[278424.967863] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[278425.025466] wlan0: Limiting TX power to 20 (23 - 3) dBm as advertised by XX:28:6d:30:13:XX
[279823.410777] wlan0: disconnect from AP XX:28:6d:30:13:XX for new auth to e0:28:6d:30:13:4c
[279823.458072] wlan0: authenticate with e0:28:6d:30:13:4c
[279823.462374] wlan0: send auth to e0:28:6d:30:13:4c (try 1/3)
[279823.487570] wlan0: send auth to e0:28:6d:30:13:4c (try 2/3)
[279823.490366] wlan0: authenticated
[279823.493227] wlan0: associate with e0:28:6d:30:13:4c (try 1/3)
[279823.528668] wlan0: associate with e0:28:6d:30:13:4c (try 2/3)
[279823.536688] wlan0: RX AssocResp from e0:28:6d:30:13:4c (capab=0x1431 status=0 aid=2)
[279823.556683] wlan0: associated
[279823.565251] wlan0: Limiting TX power to 20 (20 - 0) dBm as advertised by e0:28:6d:30:13:4c
[279835.932630] wlan0: deauthenticated from e0:28:6d:30:13:4c (Reason: 2=PREV_AUTH_NOT_VALID)
[279836.240544] wlan0: authenticate with XX:28:6d:30:13:XX
[279836.245045] wlan0: send auth to XX:28:6d:30:13:XX (try 1/3)
[279836.318104] wlan0: authenticated
[279836.318548] wlan0: associate with XX:28:6d:30:13:XX (try 1/3)
[279836.330566] wlan0: associate with XX:28:6d:30:13:XX (try 2/3)
[279836.332309] wlan0: RX AssocResp from XX:28:6d:30:13:XX (capab=0x1511 status=0 aid=1)
[279836.351027] wlan0: associated
[279836.418882] wlan0: Limiting TX power to 20 (23 - 3) dBm as advertised by XX:28:6d:30:13:XX
[281949.920882] wlan0: deauthenticating from XX:28:6d:30:13:XX by local choice (Reason: 3=DEAUTH_LEAVING)
[281962.774607] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[281963.176701] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[281963.229034] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[281969.161146] wlan0: authenticate with XX:28:6d:30:13:XX
[281969.163385] wlan0: send auth to XX:28:6d:30:13:XX (try 1/3)
[281969.238973] wlan0: authenticated
[281969.241502] wlan0: associate with XX:28:6d:30:13:XX (try 1/3)
[281969.254120] wlan0: associate with XX:28:6d:30:13:XX (try 2/3)
[281969.256021] wlan0: RX AssocResp from XX:28:6d:30:13:XX (capab=0x1511 status=0 aid=1)
[281969.274146] wlan0: associated
[281969.274203] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[281969.339422] wlan0: Limiting TX power to 20 (23 - 3) dBm as advertised by XX:28:6d:30:13:XX
[281995.444539] wlan0: disconnect from AP XX:28:6d:30:13:XX for new auth to e0:28:6d:30:13:4c
[281995.496295] wlan0: authenticate with e0:28:6d:30:13:4c
[281995.499374] wlan0: send auth to e0:28:6d:30:13:4c (try 1/3)
[281995.523310] wlan0: send auth to e0:28:6d:30:13:4c (try 2/3)
[281995.526364] wlan0: authenticated
[281995.529733] wlan0: associate with e0:28:6d:30:13:4c (try 1/3)
[281995.570090] wlan0: associate with e0:28:6d:30:13:4c (try 2/3)
[281995.575111] wlan0: RX AssocResp from e0:28:6d:30:13:4c (capab=0x1431 status=0 aid=3)
[281995.596125] wlan0: associated
[281995.672576] wlan0: Limiting TX power to 20 (20 - 0) dBm as advertised by e0:28:6d:30:13:4c
[282357.921483] wlan0: disassociated from e0:28:6d:30:13:4c (Reason: 2=PREV_AUTH_NOT_VALID)
[282358.168335] wlan0: authenticate with XX:28:6d:30:13:XX
[282358.171174] wlan0: send auth to XX:28:6d:30:13:XX (try 1/3)
[282358.266305] wlan0: send auth to XX:28:6d:30:13:XX (try 2/3)
[282358.267972] wlan0: authenticated
[282358.269333] wlan0: associate with XX:28:6d:30:13:XX (try 1/3)
[282358.281038] wlan0: associate with XX:28:6d:30:13:XX (try 2/3)
[282358.282662] wlan0: RX AssocResp from XX:28:6d:30:13:XX (capab=0x1511 status=0 aid=1)
[282358.300939] wlan0: associated
[282358.360851] wlan0: Limiting TX power to 20 (23 - 3) dBm as advertised by XX:28:6d:30:13:XX
答案1
断开与 AP XX:28:6d:30:13:XX 的连接，以便对 e0:28:6d:30:13:4c 进行新的身份验证
看来您有两个同名的 SSID，并且您的设备正在它们之间漫游以寻找更好的连接。听起来像我的前女友！
我怀疑它们是路由器的 2.4 gHz 和 5 gHz 段。我建议您重命名它们以区分它们。我建议使用 router2.4 和 router5 或类似名称。在完成我推荐的所有更改后，看看哪个段提供最佳速度并坚持下去。
请检查路由器中的无线设置。首选 WPA2-AES；而不是任何 WPA 和 WPA2 混合模式，当然也不是 TKIP。其次，如果您的路由器支持 N 速度，那么使用 2.4 GHz 频段的 20 MHz 信道宽度（而不是自动 20/40 MHz）可能会获得更好的连接性，尽管它可能会影响 N 速度。使用固定信道（1、6 或 11）比自动信道选择更幸运。此外，请确保路由器未设置为仅使用 N 速度；首选自动 B、G 和 N。进行这些更改后，重新启动路由器。
接下来，我建议明确设置你的监管范围。检查你的：
sudo iw reg get
如果您选择 00，则这是一个通用的设置。请在此处查找您的设置：http://en.wikipedia.org/wiki/ISO_3166-1_alpha-2然后暂时设置一下：
sudo iw reg set IS
当然，如果不是冰岛，请替换您的国家代码。永久设置它：
sudo nano /etc/default/crda
将最后一行改为：
REGDOMAIN=IS
仔细校对，保存并关闭文本编辑器。
接下来，确保您拥有最新的固件；检查：
sudo dpkg -s linux-firmware
我们希望您拥有 1.169.3。如果没有，请打开终端并执行以下操作：
cd /tmp
wget http://mirrors.kernel.org/ubuntu/pool/main/l/linux-firmware/linux-firmware_1.169.3_all.deb
sudo dpkg -i linux*.deb
完成所有这些更改后，请重新启动路由器和计算机，然后告诉我们是否有任何改进。