5.4.0-77-通用模块 e1000e 抱怨硬件错误

5.4.0-77-通用模块 e1000e 抱怨硬件错误

昨天我更新了我的 lubuntu 20.04,它附带了一个新内核。我今天启动它并得到

dmesg | grep -i hard
[    0.040601] Booting paravirtualized kernel on bare hardware
[    7.514435] e1000e 0000:00:19.0 0000:00:19.0 (uninitialized): Hardware Error
[   10.261171] systemd[1]: Condition check resulted in Rebuild Hardware Database being skipped.
[   14.944977] e1000e 0000:00:19.0 eth0: Hardware Error

因此我在 dmesg 中搜索之前使用 linux-image-5.4.0-74-generic 启动的情况

grep -i hard /var/log/dmesg.0
[    0.039776] kernel: Booting paravirtualized kernel on bare hardware
[    4.091866] systemd[1]: Condition check resulted in Rebuild Hardware Database being skipped.

相关硬件细节

sudo lshw -c network
  *-network                 
       description: Ethernet interface
       product: 82579LM Gigabit Network Connection (Lewisville)
       vendor: Intel Corporation
       physical id: 19
       bus info: pci@0000:00:19.0
       logical name: eth0
       version: 04
       serial: 00:21:cc:ce:85:21
       capacity: 1Gbit/s
       width: 32 bits
       clock: 33MHz
       capabilities: pm msi bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt-fd autonegotiation
       configuration: autonegotiation=on broadcast=yes driver=e1000e driverversion=3.2.6-k firmware=0.13-3 latency=0 link=no multicast=yes port=twisted pair
       resources: irq:29 memory:f2500000-f251ffff memory:f253b000-f253bfff ioport:5080(size=32)

我找到了启动选项

pcie_aspm=off

但这不会停用所有 pci 设备的 Active State Power Management 吗?还是我错了?我看看

modinfo e1000e | fgrep parm
parm:           debug:Debug level (0=none,...,16=all) (int)
parm:           copybreak:Maximum size of packet that is copied to a new buffer on receive (uint)
parm:           TxIntDelay:Transmit Interrupt Delay (array of int)
parm:           TxAbsIntDelay:Transmit Absolute Interrupt Delay (array of int)
parm:           RxIntDelay:Receive Interrupt Delay (array of int)
parm:           RxAbsIntDelay:Receive Absolute Interrupt Delay (array of int)
parm:           InterruptThrottleRate:Interrupt Throttling Rate (array of int)
parm:           IntMode:Interrupt Mode (array of int)
parm:           SmartPowerDownEnable:Enable PHY smart power down (array of int)
parm:           KumeranLockLoss:Enable Kumeran lock loss workaround (array of int)
parm:           WriteProtectNVM:Write-protect NVM [WARNING: disabling this can lead to corrupted NVM] (array of int)
parm:           CrcStripping:Enable CRC Stripping, disable if your BMC needs the CRC (array of int)

是否有可能停用我的以太网卡的电源管理?

注意,我不知道卡在这种状态下是否可以工作(这里没有路由器)。

答案1

请尝试使用 pcie_aspm=off 内核参数启动内核。

相关内容