我正在尝试创建一个桥接口清除Linux与 systemd-network 最终将其用于 KVM。
我尝试创建以下文件作为这指导:
/etc/systemd/network/br0.netdev
[NetDev]
Name=br0
Kind=bridge
/etc/systemd/network/br0.network
[Match]
Name=br0
[Network]
Address=10.0.0.3/16
Gateway=10.0.0.1
DNS=10.0.0.1
上行网络
[Match]
Name=eno1
[Network]
Bridge=br0
重新启动后,brctl
似乎暗示eno1
接口未正确连接到br0
:
bswinnerton@nuc7i3 /etc/systemd/network $ brctl show
bridge name bridge id STP enabled interfaces
br0 8000.429f5774d8b6 no
这是输出networkctl
:
bswinnerton@nuc7i3 /etc/systemd/network $ sudo networkctl
IDX LINK TYPE OPERATIONAL SETUP
1 lo loopback carrier unmanaged
2 br0 ether no-carrier configuring
3 eno1 ether routable configured
3 links listed.
以及状态systemd-networkd
:
bswinnerton@nuc7i3 /etc/systemd/network $ systemctl status systemd-networkd
● systemd-networkd.service - Network Service
Loaded: loaded (/usr/lib/systemd/system/systemd-networkd.service; enabled; vendor preset: disabled)
Active: active (running) since Tue 2017-12-19 22:45:53 UTC; 8min ago
Docs: man:systemd-networkd.service(8)
Main PID: 253 (systemd-network)
Status: "Processing requests..."
Tasks: 1 (limit: 4915)
CGroup: /system.slice/systemd-networkd.service
└─253 /usr/lib/systemd/systemd-networkd
Dec 19 22:45:53 nuc7i3 systemd-networkd[253]: br0: netdev ready
Dec 19 22:45:53 nuc7i3 systemd-networkd[253]: Enumeration completed
Dec 19 22:45:53 nuc7i3 systemd-networkd[253]: br0: IPv6 successfully enabled
Dec 19 22:45:53 nuc7i3 systemd[1]: Started Network Service.
Dec 19 22:45:53 nuc7i3 systemd-networkd[253]: eth0: Renamed to eno1
Dec 19 22:45:53 nuc7i3 systemd-networkd[253]: eno1: IPv6 successfully enabled
Dec 19 22:45:58 nuc7i3 systemd-networkd[253]: eno1: Gained carrier
Dec 19 22:45:59 nuc7i3 systemd-networkd[253]: eno1: DHCPv4 address 10.0.0.3/24 via 10.0.0.1
Dec 19 22:46:01 nuc7i3 systemd-networkd[253]: eno1: Gained IPv6LL
Dec 19 22:46:13 nuc7i3 systemd-networkd[253]: eno1: Configured
我是否错误配置了文件?对于它的价值,我尝试过sudo brctl addbr br0
,sudo brctl addif br0 eno1
然后sudo systemctl restart systemd-networkd
,一切都按预期工作,但在重新启动之间不会持续存在。
答案1
检查/lib/systemd/network/
或中的配置文件/run/systemd/network
,似乎有其他配置文件与您的eno1
接口匹配并在其上启动 DHCP