☰

LEDE 无法创建调制解调器接口

tag-icon • tag-icon networking network-interface openwrt modem lede
LEDE 无法创建调制解调器接口

系统：洋葱 Omega2s LEDE 17.01

我已将华为 ME90E 调制解调器连接到 Omega2s 的 USB 端口。

我已成功将 ME906E 调制解调器连接到运行 Debian 的 Raspberry Pi，但 Omega2 上的 LEDE 出现问题。

我已经尝试了很多次，但仍然没有成功地启动界面。

我一定错过了什么。

任何帮助表示赞赏。

跑步消息确认调制解调器已被识别：

[12.556027] usbserial：为 GSM 调制解调器（1 端口）注册的 USB 串行支持

[12.563783]选项1-1：2.2：检测到GSM调制解调器（1端口）转换器

[12.570351] USB 1-1：GSM调制解调器（1端口）转换器现在连接到ttyUSB0

[12.577378]选项1-1：2.3：检测到GSM调制解调器（1端口）转换器

[12.583884] USB 1-1：GSM调制解调器（1端口）转换器现在连接到ttyUSB1

[12.590910]选项1-1：2.4：检测到GSM调制解调器（1端口）转换器

[12.597470] USB 1-1：GSM调制解调器（1端口）转换器现在连接到ttyUSB2

创建端口 /dev/ttyUSB0、/dev/ttyUSB1 和 /dev/ttyUSB2。我跑

minicom -D /dev/ttyUSB2 115200

与调制解调器通信，我可以通过运行成功连接到系统运营商的网络

AT^NDISDUP=1,1,"apn"

文件 /sys/kernel/debug/usb/devices 包含

T:  Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#=  2 Spd=480  MxCh= 0
D:  Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs=  3
P:  Vendor=12d1 ProdID=1573 Rev= 2.28
S:  Manufacturer=HUAWEI Technology
S:  Product=HUAWEI Mobile
S:  SerialNumber=0123456712ABCA17
C:  #Ifs= 6 Cfg#= 1 Atr=a0 MxPwr=500mA
I:  If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=02 Driver=
E:  Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:  If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=03 Driver=
E:  Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:  If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=01 Prot=01 Driver=
E:  Ad=84(I) Atr=03(Int.) MxPS=  10 Ivl=32ms
E:  Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:  If#= 3 Alt= 0 #EPs= 3 Cls=0b(scard) Sub=00 Prot=00 Driver=
E:  Ad=85(I) Atr=03(Int.) MxPS=   4 Ivl=32ms
E:  Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:  If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=01 Prot=07 Driver=
E:  Ad=88(I) Atr=03(Int.) MxPS=   8 Ivl=32ms
E:  Ad=87(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:  If#= 5 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=05 Driver=
E:  Ad=89(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=06(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
C:* #Ifs= 5 Cfg#= 2 Atr=a0 MxPwr=500mA
I:* If#= 0 Alt= 0 #EPs= 1 Cls=02(comm.) Sub=06 Prot=00 Driver=(none)
E:  Ad=82(I) Atr=03(Int.) MxPS=  16 Ivl=32ms
I:* If#= 1 Alt= 0 #EPs= 0 Cls=0a(data ) Sub=00 Prot=00 Driver=(none)
I:  If#= 1 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=00 Driver=(none)
E:  Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=03 Driver=option
E:  Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=02 Driver=option
E:  Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 4 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=05 Driver=option
E:  Ad=85(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
C:  #Ifs= 3 Cfg#= 3 Atr=a0 MxPwr=500mA
A:  FirstIf#= 0 IfCount= 2 Cls=02(comm.) Sub=0e Prot=00
I:  If#= 0 Alt= 0 #EPs= 1 Cls=02(comm.) Sub=0e Prot=00 Driver=
E:  Ad=82(I) Atr=03(Int.) MxPS=  64 Ivl=32ms
I:  If#= 1 Alt= 0 #EPs= 0 Cls=0a(data ) Sub=00 Prot=02 Driver=
I:  If#= 1 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=02 Driver=
E:  Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:  If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=05 Driver=
E:  Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms

文件/etc/config/network修改为添加

config interface 'usb0'
     option ifname 'usb0'
     option proto 'dhcp'

我尝试了两种方法 - 重新启动系统并运行

/etc/init.d/network reload

当系统启动或网络重新加载时，我运行IP地址并且 usb0 仍然没有出现

1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN qlen 1
    link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
    inet 127.0.0.1/8 scope host lo
       valid_lft forever preferred_lft forever
    inet6 ::1/128 scope host 
       valid_lft forever preferred_lft forever
2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc fq_codel state UNKNOWN qlen 1000
    link/ether 40:a3:6b:c0:3a:01 brd ff:ff:ff:ff:ff:ff
    inet 192.168.0.149/24 brd 192.168.0.255 scope global eth0
       valid_lft forever preferred_lft forever
    inet6 fe80::42a3:6bff:fec0:3a01/64 scope link 
       valid_lft forever preferred_lft forever
3: ra0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc fq_codel master br-wlan state UNKNOWN qlen 1000
    link/ether 40:a3:6b:c0:39:ff brd ff:ff:ff:ff:ff:ff
    inet6 fe80::42a3:6bff:fec0:39ff/64 scope link 
       valid_lft forever preferred_lft forever
4: br-wlan: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue state UP qlen 1000
    link/ether 40:a3:6b:c0:39:ff brd ff:ff:ff:ff:ff:ff
    inet 192.168.3.1/24 brd 192.168.3.255 scope global br-wlan
       valid_lft forever preferred_lft forever
    inet6 fd1d:48c4:7633::1/60 scope global 
       valid_lft forever preferred_lft forever
    inet6 fe80::42a3:6bff:fec0:39ff/64 scope link 
       valid_lft forever preferred_lft forever
5: apcli0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc fq_codel state UNKNOWN qlen 1000
    link/ether 40:a3:6b:c0:39:00 brd ff:ff:ff:ff:ff:ff
    inet6 fe80::42a3:6bff:fec0:3900/64 scope link 
       valid_lft forever preferred_lft forever

相关内容