我想知道如何实现这样的配置，即从不计算 TX 字节和数据包？但是环回接口上有大量流量。服务器运行 RHEL 6 并在 802.3ad 绑定配置中使用两个 10Gb 以太网接口。它是一个具有中等网络流量的 NFS 客户端和应用程序服务器。
正常运行时间
$ uptime
11:12:14 up 127 days, 22:20, 2 users, load average: 7.86, 8.31, 7.14
接口统计
$ ifconfig
bond0 Link encap:Ethernet HWaddr xx:yy:de:ad:be:ef
inet addr:10.1.1.1 Bcast:10.1.1.255 Mask:255.255.255.0
inet6 addr: fe80::1602:ecff:fe6c:6248/64 Scope:Link
UP BROADCAST RUNNING MASTER MULTICAST MTU:1500 Metric:1
RX packets:78754933233 errors:12 dropped:0 overruns:0 frame:12
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:83417317310129 (75.8 TiB) TX bytes:0 (0.0 b)
eth8 Link encap:Ethernet HWaddr xx:yy:de:ad:be:ef
UP BROADCAST RUNNING SLAVE MULTICAST MTU:1500 Metric:1
RX packets:56120366224 errors:3 dropped:0 overruns:0 frame:3
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:60876314731840 (55.3 TiB) TX bytes:0 (0.0 b)
eth10 Link encap:Ethernet HWaddr xx:yy:de:ad:be:ef
UP BROADCAST RUNNING SLAVE MULTICAST MTU:1500 Metric:1
RX packets:22634567048 errors:9 dropped:0 overruns:0 frame:9
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:22541002608976 (20.5 TiB) TX bytes:0 (0.0 b)
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:65536 Metric:1
RX packets:968312148 errors:0 dropped:0 overruns:0 frame:0
TX packets:968312148 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:14257112447341 (12.9 TiB) TX bytes:14257112447341 (12.9 TiB)
键合配置
$ cat /proc/net/bonding/bond0
Ethernet Channel Bonding Driver: v3.6.0 (September 26, 2009)
Bonding Mode: IEEE 802.3ad Dynamic link aggregation
Transmit Hash Policy: layer2 (0)
MII Status: up
MII Polling Interval (ms): 100
Up Delay (ms): 0
Down Delay (ms): 0
802.3ad info
LACP rate: fast
Aggregator selection policy (ad_select): stable
Active Aggregator Info:
Aggregator ID: 2
Number of ports: 2
Actor Key: 33
Partner Key: 33873
Partner Mac Address: xx:yy:zz:aa:bb:cc
Slave Interface: eth10
MII Status: up
Speed: 10000 Mbps
Duplex: full
Link Failure Count: 1
Permanent HW addr: xx:yy:de:ad:be:ef
Aggregator ID: 2
Slave queue ID: 0
Slave Interface: eth8
MII Status: up
Speed: 10000 Mbps
Duplex: full
Link Failure Count: 2
Permanent HW addr: xx:yy:de:ad:be:af
Aggregator ID: 2
Slave queue ID: 0