我在连接到 Mikrotik CSS326-24G-2S+RM（每台通过 Mikrotik S+RJ10 SFP）的两台 PC 上各使用一张 ASUS XG-C100C 网卡。
一台 PC 非常近（2 米 Cat5E 电缆），另一台则很远（15 米 Cat5E 电缆）。两条链路都达到了惊人的 10Gbit 速度。一切都运行正常，直到我稍微触碰 SFP+ 模块或 RJ-45 连接器。如果没有触碰，链路至少可以正常工作一个月而不会出现问题（尚未测试更长时间）。如果触碰，链路会立即断开，然后开始出现随机中断。下一次中断可能发生在几分钟或几小时内 - 不可预测。
我使用最新的 RouterOS 和固件。唯一似乎有帮助的是 - 我尝试将带有 SFP+ 模块的连接器更牢固地插入 SFP+ 端口，但这似乎很奇怪而且不稳定，因为即使轻微的触摸也会再次断开连接。
我做错了什么？有什么建议吗？
Mikrotik CSS326-24G-2S+RM 配置：
# nov/18/2018 14:20:22 by RouterOS 6.43.4
# software id = SUYY-DNX3
#
# model = CRS326-24G-2S+
# serial number = 763C08FD32BB
/interface bridge
add admin-mac=CC:2D:E0:D3:EC:44 auto-mac=no comment=defconf name=bridge
/interface ethernet
set [ find default-name=ether1 ] speed=100Mbps
set [ find default-name=ether2 ] speed=100Mbps
set [ find default-name=ether3 ] speed=100Mbps
set [ find default-name=ether4 ] speed=100Mbps
set [ find default-name=ether5 ] speed=100Mbps
set [ find default-name=ether6 ] speed=100Mbps
set [ find default-name=ether7 ] speed=100Mbps
set [ find default-name=ether8 ] speed=100Mbps
set [ find default-name=ether9 ] speed=100Mbps
set [ find default-name=ether10 ] speed=100Mbps
set [ find default-name=ether11 ] speed=100Mbps
set [ find default-name=ether12 ] speed=100Mbps
set [ find default-name=ether13 ] speed=100Mbps
set [ find default-name=ether14 ] speed=100Mbps
set [ find default-name=ether15 ] speed=100Mbps
set [ find default-name=ether16 ] speed=100Mbps
set [ find default-name=ether17 ] speed=100Mbps
set [ find default-name=ether18 ] speed=100Mbps
set [ find default-name=ether19 ] speed=100Mbps
set [ find default-name=ether20 ] speed=100Mbps
set [ find default-name=ether21 ] speed=100Mbps
set [ find default-name=ether22 ] speed=100Mbps
set [ find default-name=ether23 ] speed=100Mbps
set [ find default-name=ether24 ] speed=100Mbps
set [ find default-name=sfp-sfpplus1 ] advertise=10M-half,10M-full,100M-half,100M-full,1000M-half,1000M-full,2500M-full,5000M-full,10000M-full rx-flow-control=auto tx-flow-control=auto
set [ find default-name=sfp-sfpplus2 ] speed=10Gbps
/interface list
add name=WAN
add name=LAN
/interface bridge port
add bridge=bridge interface=ether1
add bridge=bridge interface=ether2
add bridge=bridge interface=ether3
add bridge=bridge interface=ether4
add bridge=bridge interface=ether5
add bridge=bridge interface=ether6
add bridge=bridge interface=ether7
add bridge=bridge interface=ether8
add bridge=bridge interface=ether9
add bridge=bridge interface=ether10
add bridge=bridge interface=ether11
add bridge=bridge interface=ether12
add bridge=bridge interface=ether13
add bridge=bridge interface=ether14
add bridge=bridge interface=ether15
add bridge=bridge interface=ether16
add bridge=bridge interface=ether17
add bridge=bridge interface=ether18
add bridge=bridge interface=ether19
add bridge=bridge interface=ether20
add bridge=bridge interface=ether21
add bridge=bridge interface=ether22
add bridge=bridge interface=ether23
add bridge=bridge interface=ether24
add bridge=bridge interface=sfp-sfpplus1
add bridge=bridge interface=sfp-sfpplus2
/interface list member
add interface=ether1 list=WAN
add interface=ether2 list=LAN
add interface=ether3 list=LAN
add interface=ether4 list=LAN
add interface=ether5 list=LAN
add interface=ether6 list=LAN
add interface=ether7 list=LAN
add interface=ether8 list=LAN
add interface=ether9 list=LAN
add interface=ether10 list=LAN
add interface=ether11 list=LAN
add interface=ether12 list=LAN
add interface=ether13 list=LAN
add interface=ether14 list=LAN
add interface=ether15 list=LAN
add interface=ether16 list=LAN
add interface=ether17 list=LAN
add interface=ether18 list=LAN
add interface=ether19 list=LAN
add interface=ether20 list=LAN
add interface=ether21 list=LAN
add interface=ether22 list=LAN
add interface=ether23 list=LAN
add interface=ether24 list=LAN
add interface=sfp-sfpplus1 list=LAN
add interface=sfp-sfpplus2 list=LAN
/ip address
add address=192.168.9.9/8 comment=defconf interface=ether2 network=192.0.0.0
/ip cloud
set ddns-enabled=yes
/ip dns
set servers=8.8.8.8
/ip route
add distance=1 gateway=192.168.9.1
/system clock
set time-zone-name=Europe/Moscow
/system leds
set 0 leds=user-led type=off
add interface=ether1 leds=ether1-led type=interface-activity
/system logging
add action=remote disabled=yes topics=error,warning,critical,info
/system routerboard settings
set boot-os=router-os silent-boot=no
答案1
通过将两根电缆都替换为 Cat6A 电缆，解决了这个问题。