我有一块 WD 黑色硬盘 (WD1002FBYS)，我想通过 SATA->USB 适配器将它连接到我的笔记本电脑，但无法使其工作，当我连接它时它会旋转然后停止，我试图重新启动笔记本电脑，它在 POST 上挂起约 5 分钟然后启动，但驱动器仍然不工作。也许 dmesg 输出会有所帮助：
[ 2006.066073] usb 2-1: new SuperSpeed Gen 1 USB device number 6 using xhci_hcd
[ 2006.096717] usb 2-1: New USB device found, idVendor=152d, idProduct=0578, bcdDevice=32.02
[ 2006.096718] usb 2-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 2006.096719] usb 2-1: Product: JMS579
[ 2006.096720] usb 2-1: Manufacturer: JMicron
[ 2006.096721] usb 2-1: SerialNumber: 5002627380546588
[ 2006.100029] scsi host2: uas
**[ 2006.100552] scsi 2:0:0:0: Direct-Access KINGSTON SA400S37480G 3202 PQ: 0 ANSI: 6**
[ 2006.102001] sd 2:0:0:0: [sdb] Spinning up disk...
过了一会儿：
[ 2119.042929] sd 2:0:0:0: [sdb] Read Capacity(16) failed: Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
[ 2119.042935] sd 2:0:0:0: [sdb] Sense Key : Not Ready [current]
[ 2119.042938] sd 2:0:0:0: [sdb] Add. Sense: Logical unit is in process of becoming ready
[ 2125.060566] sd 2:0:0:0: [sdb] Read Capacity(10) failed: Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
[ 2125.060572] sd 2:0:0:0: [sdb] Sense Key : Not Ready [current]
[ 2125.060575] sd 2:0:0:0: [sdb] Add. Sense: Logical unit is in process of becoming ready
[ 2125.061233] sd 2:0:0:0: [sdb] 0 512-byte logical blocks: (0 B/0 B)
[ 2125.061237] sd 2:0:0:0: [sdb] 0-byte physical blocks
[ 2131.078206] sd 2:0:0:0: [sdb] Test WP failed, assume Write Enabled
[ 2133.084031] sd 2:0:0:0: [sdb] Asking for cache data failed
[ 2133.084038] sd 2:0:0:0: [sdb] Assuming drive cache: write through
[ 2139.101680] sd 2:0:0:0: [sdb] Optimal transfer size 33553920 bytes not a multiple of physical block size (0 bytes)
[ 2139.107485] sd 2:0:0:0: [sdb] Spinning up disk...
我注意到金士顿 SA400S37480G，为什么它显示 KINGSTON 是 WD 驱动器，它显示的 KINGSTON 设备是我之前连接的另一个 SSD 驱动器...
lsblk 没有列出该设备。lsusb 显示Bus 002 Device 006: ID 152d:0578 JMicron Technology Corp. / JMicron USA Technology Corp. JMS567 SATA 6Gb/s bridge是否有意义。
我不是硬件专家所以如果我问了一个愚蠢的问题请原谅我，谢谢。
顺便说一句，我已经尝试通过 SATA 连接到家用电脑，它在启动时会抛出一个错误，提示辅助主硬盘错误...