无法使用 iwd 独立连接到互联网

无法使用 iwd 独立连接到互联网

我正在尝试使用连接到 WiFiiwd 独立的,没有NetworkManagerwpa_supplicant

这是在 Debian 10 机器上,有netinst安装,没有桌面环境。我将非免费组件添加到apt-sources并安装了firmware-iwlwifi

我修改/etc/iwd/main.conf如下

[General]
EnableNetworkConfiguration=true

[Network]
NameResolvingService=systemd

我曾经iwctl连接过:

[iwd]# station list
                            Devices in Station Mode                           *
--------------------------------------------------------------------------------
  Name                State          Scanning
--------------------------------------------------------------------------------
  wlp2s0              connected

[iwd]# device list
                                    Devices
--------------------------------------------------------------------------------
  Name                Address             Powered   Adapter   Mode
--------------------------------------------------------------------------------
  wlp2s0              xx:xx:xx:xx:xx:xx   on        phy0      station

这些是正在运行的服务:

UNIT                      LOAD   ACTIVE SUB     DESCRIPTION
cron.service              loaded active running Regular background program processing daemon
dbus.service              loaded active running D-Bus System Message Bus
[email protected]        loaded active running Getty on tty1
iwd.service               loaded active running Wireless service
rsyslog.service           loaded active running System Logging Service
ssh.service               loaded active running OpenBSD Secure Shell server
systemd-journald.service  loaded active running Journal Service
systemd-logind.service    loaded active running Login Service
systemd-networkd.service  loaded active running Network Service
systemd-resolved.service  loaded active running Network Name Resolution
systemd-timesyncd.service loaded active running Network Time Synchronization
systemd-udevd.service     loaded active running udev Kernel Device Manager
[email protected]            loaded active running User Manager for UID 0

LOAD   = Reflects whether the unit definition was properly loaded.
ACTIVE = The high-level unit activation state, i.e. generalization of SUB.
SUB    = The low-level unit activation state, values depend on unit type.

13 loaded units listed. Pass --all to see loaded but inactive units, too.
To show all installed unit files use 'systemctl list-unit-files'.

驱动程序已加载:

lspci | grep -i intel
02:00.0 Network controller: Intel Corporation Wireless-AC 9260 (rev 29)

我在这里没有看到任何错误:

[    4.807336] iwlwifi 0000:02:00.0 wlp2s0: renamed from wlan0
[    5.330505] IPv6: ADDRCONF(NETDEV_UP): wlp2s0: link is not ready
[    9.815999] wlp2s0: authenticate with xx:xx:xx:xx:xx:xx
[    9.825148] wlp2s0: send auth to xx:xx:xx:xx:xx:xx (try 1/3)
[    9.868608] wlp2s0: authenticated
[    9.870031] wlp2s0: associate with xx:xx:xx:xx:xx:xx (try 1/3)
[    9.874042] wlp2s0: RX AssocResp from xx:xx:xx:xx:xx:xx (capab=0x1011 status=0 aid=2)
[    9.877212] wlp2s0: associated
[    9.976363] wlp2s0: Limiting TX power to 23 (23 - 0) dBm as advertised by xx:xx:xx:xx:xx:xx
[   11.900982] IPv6: ADDRCONF(NETDEV_CHANGE): wlp2s0: link becomes ready

但我无法 ping 任何地址/主机名。

这与 相关吗dhcpcd

有任何想法吗?

相关的:通过 iwd(Linux 无线守护进程)从 Linux 系统上的命令行连接到 wifi

答案1

通过升级到 Bullseye 解决。

相关内容