使用 circuitikz 的电网

Question

我正在尝试使用 circuitikz 来绘制这个，但是在做“母线”时遇到了一些麻烦，电压源没有连接到其东边的任何东西，并且在一个分支中放置了 2 个箭头。

Answer 1

\documentclass{article}
\usepackage{tikz}
\usetikzlibrary{arrows.meta}
\pagestyle{empty}
\begin{document}
\begin{tikzpicture}[line cap=round,line join=round,x=1.0cm,y=1.0cm]
\clip(-3.21,-2.70) rectangle (7.08,5.76);
\draw [line width=1.6pt] (-1.,0.)-- (0.,0.);
\draw(-2.,0.) circle (1.cm);
\draw [line width=4.4pt] (0.,1.)-- (0.,-1.);
\draw (0.,0.65)-- (0.5,0.65);
\draw (0.5,0.65)-- (3.9,3.52);
\draw (3.91,3.52)-- (3.91,4.);
\draw [line width=1.2pt] (0.,-0.65)-- (4.08,-0.65);
\draw (4.08,-0.65)-- (4.08,-1.21);
\draw (5.,4.01)-- (5.,-1.21);
\draw [line width=4.4pt] (3.69,4.00)-- (5.30,4.00);
\draw [line width=4.4pt] (3.70,-1.21)-- (5.32,-1.20);
\draw [-{Stealth[scale=1.3,angle'=45,open]},semithick] (4.5,4.00) -- (4.5,5.1);
\draw [-{Stealth[scale=1.3,angle'=45,open]},semithick] (4.56,-1.21) -- (4.56,-2.21);
\draw (-2.44,0.3) node[anchor=north west] {\Huge $\mathbf{\sim}$};
\draw (-0.18,1.6) node[anchor=north west] {$1$};
\draw (4.36,-0.22) node[anchor=north west] {$2$};
\draw (4.24,3.7) node[anchor=north west] {$3$};
\draw (-0.37,-1.1) node[anchor=north west] {$V_1$};
\draw (0.56,-0.80) node[anchor=north west] {$P_{12}$};
\draw (2.77,-0.80) node[anchor=north west] {$Q_{12}$};
\draw (5.79,4.56) node[anchor=north west] {$V_1$};
\draw (5.86,-0.55) node[anchor=north west] {$V_2$};
\draw (1.34,1.3) node[anchor=north west] {$P_{13}$};
\draw (3.35,2.90) node[anchor=north west] {$Q_{31}$};
\draw [-{Stealth[scale=1.3,angle'=45,open]},semithick] (1.09,0.84) -- (2.12,1.70);
\draw [-{Stealth[scale=1.3,angle'=45,open]},semithick] (3.8,3.1) -- (2.76,2.27);
\draw [-{Stealth[scale=1.3,angle'=45,open]},semithick] (0.34,-0.84) -- (1.5,-0.84);
\draw [-{Stealth[scale=1.3,angle'=45,open]},semithick] (3.7,-0.82) -- (2.4,-0.82);
\end{tikzpicture}
\end{document}