☰

HP DL180 G6 琥珀色灯，但驱动器正常

tag-icon • tag-icon hp hp-proliant hp-smart-array
HP DL180 G6 琥珀色灯，但驱动器正常

我们有一台 HP DL180 G6，配有 25 个 SFF SATA 驱动器，运行 64 位 Debian Linux。最近有一个驱动器出现故障，因此我们用 HP 提供的全新相同部件替换了故障驱动器。磁盘控制器重建了逻辑卷，hpacucli 命令现在显示逻辑驱动器和物理驱动器均正常。但是，驱动器的前挡板上仍然有稳定的琥珀色指示灯。另一位系统管理员告诉我，当他更换另一个驱动器时发生了这种情况，重新启动服务器后问题就解决了。我真的不想重新启动这台服务器，因为它即将投入生产，我不想每次驱动器出现故障时都要重新启动。还有其他方法可以将前 LED 改回绿色吗？

编辑：按照@ewwhite 的要求添加 hpcaucli 输出

root@debian:~# hpacucli ctrl all show config

Smart Array P410 in Slot 3                (sn: PACCR9VYCJ2V  )

   array A (SATA, Unused Space: 0  MB)


      logicaldrive 1 (149.0 GB, RAID 1, OK)

      physicaldrive 1I:1:0 (port 1I:box 1:bay 0, SATA, 160 GB, OK)
      physicaldrive 1I:1:0 (port 1I:box 1:bay 0, SATA, 160 GB, OK)

   array B (SATA, Unused Space: 0  MB)


      logicaldrive 2 (9.1 TB, RAID 50, OK)

      physicaldrive 1I:1:0 (port 1I:box 1:bay 0, SATA, 500 GB, OK)
      physicaldrive 1I:1:0 (port 1I:box 1:bay 0, SATA, 500 GB, OK)
      physicaldrive 1I:1:0 (port 1I:box 1:bay 0, SATA, 500 GB, OK)
      physicaldrive 1I:1:0 (port 1I:box 1:bay 0, SATA, 500 GB, OK)
      physicaldrive 1I:1:0 (port 1I:box 1:bay 0, SATA, 500 GB, OK)
      physicaldrive 1I:1:0 (port 1I:box 1:bay 0, SATA, 500 GB, OK)
      physicaldrive 1I:1:0 (port 1I:box 1:bay 0, SATA, 500 GB, OK)
      physicaldrive 1I:1:0 (port 1I:box 1:bay 0, SATA, 500 GB, OK)
      physicaldrive 1I:1:0 (port 1I:box 1:bay 0, SATA, 500 GB, OK)
      physicaldrive 1I:1:0 (port 1I:box 1:bay 0, SATA, 500 GB, OK)
      physicaldrive 1I:1:0 (port 1I:box 1:bay 0, SATA, 500 GB, OK)
      physicaldrive 1I:1:0 (port 1I:box 1:bay 0, SATA, 500 GB, OK)
      physicaldrive 1I:1:0 (port 1I:box 1:bay 0, SATA, 500 GB, OK)
      physicaldrive 1I:1:0 (port 1I:box 1:bay 0, SATA, 500 GB, OK)
      physicaldrive 1I:1:0 (port 1I:box 1:bay 0, SATA, 500 GB, OK)
      physicaldrive 1I:1:0 (port 1I:box 1:bay 0, SATA, 500 GB, OK)
      physicaldrive 1I:1:0 (port 1I:box 1:bay 0, SATA, 500 GB, OK)
      physicaldrive 1I:1:0 (port 1I:box 1:bay 0, SATA, 500 GB, OK)
      physicaldrive 1I:1:0 (port 1I:box 1:bay 0, SATA, 500 GB, OK)
      physicaldrive 1I:1:0 (port 1I:box 1:bay 0, SATA, 500 GB, OK)
      physicaldrive 1I:1:0 (port 1I:box 1:bay 0, SATA, 500 GB, OK)
      physicaldrive 1I:1:0 (port 1I:box 1:bay 0, SATA, 500 GB, OK)
      physicaldrive 1I:1:0 (port 1I:box 1:bay 0, SATA, 500 GB, OK, spare)

   Enclosure SEP (Vendor ID HP, Model DL18x25SFF) 248 (WWID: 500E004AAAAAAA3E, Port: 1I, Box: 1)

   Expander 250 (WWID: 500E004AAAAAAA3F, Port: 1I, Box: 1)

   SEP (Vendor ID PMCSIERA, Model  SRC 8x6G) 249 (WWID: 500143800674C4BF)

root@debian:~# hpacucli ctrl all show detail;

Smart Array P410 in Slot 3
   Bus Interface: PCI
   Slot: 3
   Serial Number: PACCR9VYCJ2V
   Cache Serial Number: PAAVP9VYFFHP
   RAID 6 (ADG) Status: Disabled
   Controller Status: OK
   Hardware Revision: C
   Firmware Version: 5.70
   Rebuild Priority: Medium
   Expand Priority: Medium
   Surface Scan Delay: 3 secs
   Surface Scan Mode: Idle
   Queue Depth: Automatic
   Monitor and Performance Delay: 60  min
   Elevator Sort: Enabled
   Degraded Performance Optimization: Disabled
   Inconsistency Repair Policy: Disabled
   Wait for Cache Room: Disabled
   Surface Analysis Inconsistency Notification: Disabled
   Post Prompt Timeout: 15 secs
   Cache Board Present: True
   Cache Status: OK
   Cache Ratio: 25% Read / 75% Write
   Drive Write Cache: Disabled
   Total Cache Size: 512 MB
   Total Cache Memory Available: 400 MB
   No-Battery Write Cache: Disabled
   Cache Backup Power Source: Batteries
   Battery/Capacitor Count: 1
   Battery/Capacitor Status: OK
   SATA NCQ Supported: True

答案1

所以这就是我要做的。

您拥有的 HP ProLiant DL180 G6 型号是 25 托架设备。驱动器背板上嵌入了一个 SAS 扩展器，两条 SAS SFF-8087 电缆连接到 HP Smart Array P410 PCIe 控制器。

部分原因就是为什么您会看到奇怪的港口：海湾演示。

我会升级背板固件，并将您的 P410 控制器升级到最新修订版 6.40。您应该能够使用HP ProLiant DVD 服务包。

相关内容