lvs 命令找不到 LVM 分区,使用什么工具与这些分区进行交互?

lvs 命令找不到 LVM 分区,使用什么工具与这些分区进行交互?

执行时fdisk -l有两个“Linux LVM”分区,但使用时lvs不返回任何内容并lvmdiskscan返回“0 LVM 物理卷”。

我应该使用什么工具来与这些分区交互?(缩小、调整大小等)

sudo fdisk -l给出

Disk /dev/sda: 477 GiB, 512110190592 bytes, 1000215216 sectors
Units: sectors of 1 * 512 = 512 bytes
Sector size (logical/physical): 512 bytes / 512 bytes
I/O size (minimum/optimal): 512 bytes / 512 bytes
Disklabel type: gpt
Disk identifier: CED3CBCF-A524-4E54-8A0D-0341958E40C2

Device         Start        End   Sectors   Size Type
/dev/sda1       2048       4095      2048     1M BIOS boot
/dev/sda2       4096    1052671   1048576   512M Linux LVM
/dev/sda3    1052672  868701837 867649166 413.7G Linux LVM
/dev/sda4  868702208 1000215182 131512975  62.7G Linux swap


Disk /dev/sdc: 477 GiB, 512110190592 bytes, 1000215216 sectors
Units: sectors of 1 * 512 = 512 bytes
Sector size (logical/physical): 512 bytes / 512 bytes
I/O size (minimum/optimal): 512 bytes / 512 bytes


Disk /dev/sdb: 477 GiB, 512110190592 bytes, 1000215216 sectors
Units: sectors of 1 * 512 = 512 bytes
Sector size (logical/physical): 512 bytes / 512 bytes
I/O size (minimum/optimal): 512 bytes / 512 bytes

lvmdiskscan给出

  /dev/sda2 [     512.00 MiB]
  /dev/sda3 [     413.73 GiB]
  /dev/sda4 [      62.71 GiB]
  /dev/sdb  [     476.94 GiB]
  /dev/sdc  [     476.94 GiB]
  2 disks
  3 partitions
  0 LVM physical volume whole disks
  0 LVM physical volumes

df给出

Filesystem      Size  Used Avail Use% Mounted on
dev              32G     0   32G   0% /dev
run              32G  628K   32G   1% /run
/dev/sda3        79G  1.2G   74G   2% /
tmpfs            32G     0   32G   0% /dev/shm
tmpfs            32G     0   32G   0% /sys/fs/cgroup
tmpfs            32G     0   32G   0% /tmp
/dev/sda2       488M   28M  425M   7% /boot
tmpfs           6.3G     0  6.3G   0% /run/user/1000

pvscan返回

No matching physical volumes found

vgscan返回

Reading volume groups from cache.

vgs并且pvs不返回任何内容

从 Ubuntu 14.04 实时 CD执行操作时fdisk -l,分区被报告为Linux而不是Linux LVM,其 ID 为 83 而不是 8e,可能是安装在 arch 安装上的工具错误地将分区检测为 LVM,而 LVM 工具知道它们不是 LVM 分区并忽略它们?

相关内容