☰

Emulex OC10 CNA 卡 be2net twinax 无链接

tag-icon • tag-icon debian proxmox emulex
Emulex OC10 CNA 卡 be2net twinax 无链接

最近，我们购买了 3 个 Emulex OC10 卡，用于我们的 proxmox 测试设置。它们是 IBM 型号 49Y4201。目标是在 Linux 中设置正常的 10G 以太网连接（因此没有 iSCSI 或 FCoE）。这些卡似乎在系统中工作正常，您可以进入固件 BIOS 并进行设置，然后闪烁两个端口上的 LED 等。

在操作系统中，be2net 驱动程序已加载，并抱怨固件过旧和中断丢失，因此经过一番周折后，我刷新了较新的 4.1 固件。经过验证和重新启动后，它再次能够进入 BIOS。

使用 proxmox 或 ifconfig 设置两个 NIC，然后 ifup 给出如下内核​​消息：

[80221.424544] be2net 0000:21:00.0 enp33s0f0: Link is Down
[80292.286008] be2net 0000:21:00.1 enp33s0f1: Link is Down

在另一台主机上

[79712.635565] be2net 0000:21:00.0 enp33s0f0: Link is Down
[79716.421629] be2net 0000:21:00.1 enp33s0f1: Link is Down

我们拥有的电缆是思科品牌的 SFP-H10GB-CU3M，它们在 IBM 网站上被列为受支持，但是插入电缆时卡上没有链接 LED 亮起。

两台主机上的 ethtool 的输出：

Settings for enp33s0f0:
        Supported ports: [ FIBRE ]
        Supported link modes:   1000baseT/Full 
                                10000baseT/Full 
        Supported pause frame use: Symmetric
        Supports auto-negotiation: No
        Supported FEC modes: Not reported
        Advertised link modes:  Not reported
        Advertised pause frame use: No
        Advertised auto-negotiation: No
        Advertised FEC modes: Not reported
        Speed: Unknown!
        Duplex: Unknown! (255)
        Port: FIBRE
        PHYAD: 1
        Transceiver: internal
        Auto-negotiation: off
        Supports Wake-on: d
        Wake-on: d
        Current message level: 0x00002000 (8192)
                               hw
        Link detected: no

be2net 驱动程序信息：

[    1.077098] be2net 0000:21:00.0: be2net version is 12.0.0.0
[    1.077106] be2net 0000:21:00.0: enabling device (0000 -> 0002)
[    1.077422] be2net 0000:21:00.0: PCIe error reporting enabled
[    3.252360] be2net 0000:21:00.0: FW config: function_mode=0x20003, function_caps=0x7
[    3.372359] be2net 0000:21:00.0: Max: txqs 1, rxqs 5, rss 4, eqs 16, vfs 0
[    3.372361] be2net 0000:21:00.0: Max: uc-macs 30, mc-macs 64, vlans 15
[    3.372446] be2net 0000:21:00.0: enabled 1 MSI-x vector(s) for NIC
[    3.480586] be2net 0000:21:00.0: created 1 TX queue(s)
[    3.504350] be2net 0000:21:00.0: created 1 RX queue(s)
[    3.603279] be2net 0000:21:00.0: FW version is 4.1.334.36
[    3.609848] be2net 0000:21:00.0: HW Flow control - TX:1 RX:1
[    3.617493] be2net 0000:21:00.0: Adapter does not support HW error recovery
[    3.617678] be2net 0000:21:00.0: Emulex OneConnect: PF vNIC-2 port 0
[    3.617705] be2net 0000:21:00.1: be2net version is 12.0.0.0
[    3.617712] be2net 0000:21:00.1: enabling device (0000 -> 0002)
[    3.617924] be2net 0000:21:00.1: PCIe error reporting enabled
[    3.868352] be2net 0000:21:00.1: FW config: function_mode=0x20003, function_caps=0x7
[    3.988362] be2net 0000:21:00.1: Max: txqs 1, rxqs 5, rss 4, eqs 16, vfs 0
[    3.988364] be2net 0000:21:00.1: Max: uc-macs 30, mc-macs 64, vlans 15
[    3.988449] be2net 0000:21:00.1: enabled 1 MSI-x vector(s) for NIC
[    4.096359] be2net 0000:21:00.1: created 1 TX queue(s)
[    4.120348] be2net 0000:21:00.1: created 1 RX queue(s)
[    4.242124] be2net 0000:21:00.1: FW version is 4.1.334.36
[    4.248700] be2net 0000:21:00.1: HW Flow control - TX:1 RX:1
[    4.256697] be2net 0000:21:00.1: Adapter does not support HW error recovery
[    4.256884] be2net 0000:21:00.1: Emulex OneConnect: PF vNIC-2 port 1
[    4.257756] be2net 0000:21:00.1 enp33s0f1: renamed from eth1
[    4.272475] be2net 0000:21:00.0 enp33s0f0: renamed from eth0
[80221.424544] be2net 0000:21:00.0 enp33s0f0: Link is Down
[80292.286008] be2net 0000:21:00.1 enp33s0f1: Link is Down

有人知道如何解决这个问题吗？我遗漏了什么吗？

答案1

这些适配器需要通过 Emulex（现为 Broadcom）工具重置：

toolname SetPortEnabled MAC-ADDRESS 0
toolname SetPortEnabled MAC-ADDRESS 1

工具名称-取决于操作系统和工具的版本

MAC-ADDRESS - 适配器的 MAC 地址

我的系统中的示例：

brcmhbacmd SetPortEnabled '00-90-fa-22-66-5c' 0
brcmhbacmd SetPortEnabled '00-90-fa-22-66-60' 0

brcmhbacmd SetPortEnabled '00-90-fa-22-66-5c' 1
brcmhbacmd SetPortEnabled '00-90-fa-22-66-60' 1

相关内容