经过一番对角线处理后，我发现我的无线网络还没有解决，但是我的有线连接却误报了错误的图标。
eth0 Link encap:Ethernet HWaddr 20:6a:8a:3f:70:90
inet addr:172.29.2.181 Bcast:172.29.15.255 Mask:255.255.240.0
inet6 addr: fe80::226a:8aff:fe3f:7090/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:3328 errors:0 dropped:0 overruns:0 frame:0
TX packets:1414 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:1324723 (1.3 MB) TX bytes:260711 (260.7 KB)
Interrupt:19
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:79866 errors:0 dropped:0 overruns:0 frame:0
TX packets:79866 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:10583710 (10.5 MB) TX bytes:10583710 (10.5 MB)
WARNING: you should run this program as super-user.
*-network UNCLAIMED
description: Network controller
product: AR9287 Wireless Network Adapter (PCI-Express)
vendor: Qualcomm Atheros
physical id: 0
bus info: pci@0000:03:00.0
version: 01
width: 64 bits
clock: 33MHz
capabilities: cap_list
configuration: latency=0
resources: memory:f1600000-f160ffff
*-network
description: Ethernet interface
product: NetLink BCM57785 Gigabit Ethernet PCIe
vendor: Broadcom Corporation
physical id: 0
bus info: pci@0000:04:00.0
logical name: eth0
version: 10
serial: 20:6a:8a:3f:70:90
size: 100Mbit/s
capacity: 1Gbit/s
width: 64 bits
clock: 33MHz
capabilities: bus_master cap_list rom ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation
configuration: autonegotiation=on broadcast=yes driver=tg3 driverversion=3.123 duplex=full firmware=sb ip=172.29.2.181 latency=0 multicast=yes port=twisted pair speed=100Mbit/s
resources: irq:19 memory:f1400000-f140ffff memory:f1410000-f141ffff memory:f1450000-f14507ff
警告：输出可能不完整或不准确，您应该以超级用户身份运行该程序。
有人可以帮忙吗？
根据 Chili555 的说法，我尝试过 modprobe ath9k && dmesg | grep ath
[339970.692404] ath: phy0: Chip reset failed
[339970.692409] ath: phy0: Unable to reset hardware; reset status -22 (freq 2412 MHz)
[339970.809499] ath: phy0: Chip reset failed
[339970.809504] ath: phy0: Unable to reset hardware; reset status -22 (freq 2412 MHz)
[339970.925151] ath: phy0: Chip reset failed
[339970.925156] ath: phy0: Unable to reset hardware; reset status -22 (freq 2412 MHz)
[340612.711783] ath: phy0: Chip reset failed
[340612.711789] ath: phy0: Unable to reset hardware; reset status -22 (freq 2412 MHz)
[340612.829633] ath: phy0: Chip reset failed
[340612.829639] ath: phy0: Unable to reset hardware; reset status -22 (freq 2412 MHz)
[340612.945773] ath: phy0: Chip reset failed
[340612.945779] ath: phy0: Unable to reset hardware; reset status -22 (freq 2412 MHz)
[340626.001522] ath: phy0: Chip reset failed
[340626.001527] ath: phy0: Unable to reset hardware; reset status -22 (freq 2412 MHz)
[346785.942351] ath: phy0: Chip reset failed
[346785.942356] ath: phy0: Unable to reset hardware; reset status -22 (freq 2412 MHz)
[346786.059931] ath: phy0: Chip reset failed
[346786.059936] ath: phy0: Unable to reset hardware; reset status -22 (freq 2412 MHz)
[346786.176004] ath: phy0: Chip reset failed
[346786.176009] ath: phy0: Unable to reset hardware; reset status -22 (freq 2412 MHz)
[347318.499218] ath: phy0: Chip reset failed
[347318.499224] ath: phy0: Unable to reset hardware; reset status -22 (freq 2412 MHz)
[347335.167438] ath: phy0: Chip reset failed
[347335.167444] ath: phy0: Unable to reset hardware; reset status -22 (freq 2412 MHz)
[347335.284839] ath: phy0: Chip reset failed
[347335.284845] ath: phy0: Unable to reset hardware; reset status -22 (freq 2412 MHz)
[347335.400957] ath: phy0: Chip reset failed
[347335.400962] ath: phy0: Unable to reset hardware; reset status -22 (freq 2412 MHz)
[348371.939924] ath: phy0: Chip reset failed
[348371.939929] ath: phy0: Unable to reset hardware; reset status -22 (freq 2412 MHz)
[349456.895035] ath9k: ath9k: Driver unloaded
[349465.420567] ath9k 0000:03:00.0: enabling device (0000 -> 0002)
[349465.535474] ath: phy1: Couldn't reset chip
[349465.535478] ath: phy1: Unable to initialize hardware; initialization status: -5
[349465.535484] ath9k 0000:03:00.0: Failed to initialize device
[349465.535575] ath9k: probe of 0000:03:00.0 failed with error -5
[349648.631049] ath9k: ath9k: Driver unloaded
[349658.068003] ath: phy2: Couldn't reset chip
[349658.068008] ath: phy2: Unable to initialize hardware; initialization status: -5
[349658.068014] ath9k 0000:03:00.0: Failed to initialize device
[349658.068066] ath9k: probe of 0000:03:00.0 failed with error -5
[427830.275860] ath9k: ath9k: Driver unloaded
[427833.430991] ath: phy3: Couldn't reset chip
[427833.431006] ath: phy3: Unable to initialize hardware; initialization status: -5
[427833.431023] ath9k 0000:03:00.0: Failed to initialize device
[427833.431280] ath9k: probe of 0000:03:00.0 failed with error -5
[428873.448746] ath9k: ath9k: Driver unloaded
[429026.303871] ath: phy4: Couldn't reset chip
[429026.303877] ath: phy4: Unable to initialize hardware; initialization status: -5
[429026.303882] ath9k 0000:03:00.0: Failed to initialize device
[429026.303969] ath9k: probe of 0000:03:00.0 failed with error -5
[429088.070481] ath9k: ath9k: Driver unloaded
[429115.975556] ath: phy5: Couldn't reset chip
[429115.975560] ath: phy5: Unable to initialize hardware; initialization status: -5
[429115.975565] ath9k 0000:03:00.0: Failed to initialize device
[429115.975616] ath9k: probe of 0000:03:00.0 failed with error -5
答案1
我建议您安装更高版本的驱动程序 ath9k。使用有效的有线以太网连接，打开终端并执行以下操作：
sudo apt-get install linux-backports-modules-cw-3.12-precise-generic
重启并让我们听取您的报告。如果它没有按预期工作，让我们看看：
dmesg | grep ath