我无法192.168.0.155
通过以太网访问家庭网络上的本地 Raspberry Pi 服务器 ( ),但我可以通过 wifi 完美地 ssh 到它。
我通过两个接口都可以正常连接互联网,并且在另一台 Macbook 上也出现相同的行为(可以通过 wifi 到达服务器,但不能通过以太网)。
所有以太网电缆都直接连接到我的家庭路由器(运行 DD-WRT),该路由器也充当无线接入点。
以下是我netstat -rn
在 Macbook Pro ( ) 上使用以太网(通过 Thunderbolt 坞站)时的输出192.168.0.176
:
Destination Gateway Flags Refs Use Netif Expire
default 192.168.0.1 UGSc 89 0 en6
127 127.0.0.1 UCS 1 0 lo0
127.0.0.1 127.0.0.1 UH 3 397 lo0
169.254 link#4 UCS 1 0 en6
192.168.0 link#4 UCS 4 0 en6
192.168.0.1/32 link#4 UCS 2 0 en6
192.168.0.1 c4:6e:1f:7f:1a:3e UHLWIir 90 9350 en6 1199
192.168.0.131 94:53:30:47:2:c9 UHLWIi 1 0 en6 470
192.168.0.155 link#4 UHLWIi 1 7 en6
192.168.0.176/32 link#4 UCS 1 0 en6
192.168.0.255 link#4 UHLWbI 1 72 en6
224.0.0 link#4 UmCS 2 0 en6
224.0.0.251 1:0:5e:0:0:fb UHmLWI 1 0 en6
255.255.255.255/32 link#4 UCS 2 0 en6
255.255.255.255 link#4 UHLWbI 1 28 en6
当连接到 wifi 时:
Destination Gateway Flags Refs Use Netif Expire
default 192.168.0.1 UGSc 27 0 en0
127 127.0.0.1 UCS 1 0 lo0
127.0.0.1 127.0.0.1 UH 2 397 lo0
169.254 link#5 UCS 1 0 en0
192.168.0 link#5 UCS 3 0 en0
192.168.0.1/32 link#5 UCS 2 0 en0
192.168.0.1 c4:6e:1f:7f:1a:3e UHLWIir 29 119 en0 1198
192.168.0.150/32 link#5 UCS 1 0 en0
192.168.0.155 b8:27:eb:b6:4c:34 UHLWIi 1 0 en0 1143
192.168.0.255 link#5 UHLWbI 1 26 en0
224.0.0 link#5 UmCS 2 0 en0
224.0.0.251 1:0:5e:0:0:fb UHmLWI 1 0 en0
255.255.255.255/32 link#5 UCS 2 0 en0
255.255.255.255 link#5 UHLWbI 1 2 en0
并ifconfig
输出:
lo0: flags=8049<UP,LOOPBACK,RUNNING,MULTICAST> mtu 16384
options=3<RXCSUM,TXCSUM>
inet6 ::1 prefixlen 128
inet 127.0.0.1 netmask 0xff000000
inet6 fe80::1%lo0 prefixlen 64 scopeid 0x1
nd6 options=1<PERFORMNUD>
gif0: flags=8010<POINTOPOINT,MULTICAST> mtu 1280
stf0: flags=0<> mtu 1280
en6: flags=8822<BROADCAST,SMART,SIMPLEX,MULTICAST> mtu 1500
options=b<RXCSUM,TXCSUM,VLAN_HWTAGGING>
ether 00:0c:6c:07:66:ba
nd6 options=1<PERFORMNUD>
media: autoselect (<unknown type>)
status: inactive
en0: flags=8863<UP,BROADCAST,SMART,RUNNING,SIMPLEX,MULTICAST> mtu 1500
ether 80:e6:50:0a:78:ea
inet 192.168.0.150 netmask 0xffffff00 broadcast 192.168.0.255
media: autoselect
status: active
en1: flags=963<UP,BROADCAST,SMART,RUNNING,PROMISC,SIMPLEX> mtu 1500
options=60<TSO4,TSO6>
ether 72:00:04:b0:66:30
media: autoselect <full-duplex>
status: inactive
en2: flags=963<UP,BROADCAST,SMART,RUNNING,PROMISC,SIMPLEX> mtu 1500
options=60<TSO4,TSO6>
ether 72:00:04:b0:66:31
media: autoselect <full-duplex>
status: inactive
p2p0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> mtu 2304
ether 02:e6:50:0a:78:ea
media: autoselect
status: inactive
awdl0: flags=8943<UP,BROADCAST,RUNNING,PROMISC,SIMPLEX,MULTICAST> mtu 1484
ether da:51:ce:04:6b:fd
inet6 fe80::d851:ceff:fe04:6bfd%awdl0 prefixlen 64 scopeid 0x9
nd6 options=1<PERFORMNUD>
media: autoselect
status: active
bridge0: flags=8822<BROADCAST,SMART,SIMPLEX,MULTICAST> mtu 1500
options=63<RXCSUM,TXCSUM,TSO4,TSO6>
ether 02:0c:6c:70:dc:00
Configuration:
id 0:0:0:0:0:0 priority 0 hellotime 0 fwddelay 0
maxage 0 holdcnt 0 proto stp maxaddr 100 timeout 1200
root id 0:0:0:0:0:0 priority 0 ifcost 0 port 0
ipfilter disabled flags 0x2
member: en2 flags=3<LEARNING,DISCOVER>
ifmaxaddr 0 port 7 priority 0 path cost 0
member: en1 flags=3<LEARNING,DISCOVER>
ifmaxaddr 0 port 6 priority 0 path cost 0
media: <unknown type>
status: inactive
utun0: flags=8051<UP,POINTOPOINT,RUNNING,MULTICAST> mtu 1380
inet6 fe80::818d:c5f0:c295:5130%utun0 prefixlen 64 scopeid 0xb
inet6 fd1b:90c8:de38:d6b:818d:c5f0:c295:5130 prefixlen 64
nd6 options=1<PERFORMNUD>
我已经多次重置路由,重新启动笔记本电脑和路由器,并更改 Pi 服务器上的 IP,但问题仍然存在。