我的 Imation Apollo M100 便携式磁盘无法安装。
有一天,我正在将一个沉重的文件复制到其中,该过程卡住了,我将其从计算机上拔了下来。当我将其连接回电脑并查看其文件夹时,问题就出现了。
首先,它非常慢,然后我无法在文件资源管理器中看到该驱动器,因为它没有安装。此外,当它尝试安装文件资源管理器软件时,磁盘应用程序和ls /media/cesc/
终端窗口中的操作会挂起,直到驱动器停止尝试安装。
我发现的所有内容都是关于fsck
在损坏的文件系统上运行命令,但我不能,因为它在我运行时不会出现df -h
。
这是 的输出dmesg
。它清楚地表明其中一个分区文件系统已损坏,需要修复:
[ 51.965845] init: anacron main process (1325) killed by TERM signal
[ 83.019268] usb 4-1: new SuperSpeed USB device number 2 using xhci_hcd
[ 83.038703] usb 4-1: New USB device found, idVendor=0718, idProduct=1905
[ 83.038707] usb 4-1: New USB device strings: Mfr=4, Product=5, SerialNumber=6
[ 83.038709] usb 4-1: Product: M100 USB 3
[ 83.038711] usb 4-1: Manufacturer: Imation
[ 83.038712] usb 4-1: SerialNumber: 00000000000000000000000013
[ 83.836745] usb-storage 4-1:1.0: USB Mass Storage device detected
[ 83.836810] scsi6 : usb-storage 4-1:1.0
[ 83.836871] usbcore: registered new interface driver usb-storage
[ 83.842386] usbcore: registered new interface driver uas
[ 87.830998] scsi 6:0:0:0: Direct-Access Imation M100 USB 3 0.00 PQ: 0 ANSI: 6
[ 87.831277] sd 6:0:0:0: Attached scsi generic sg3 type 0
[ 87.831649] sd 6:0:0:0: [sdc] 1953525168 512-byte logical blocks: (1.00 TB/931 GiB)
[ 87.832040] sd 6:0:0:0: [sdc] Write Protect is off
[ 87.832043] sd 6:0:0:0: [sdc] Mode Sense: 00 00 00 00
[ 87.832429] sd 6:0:0:0: [sdc] Asking for cache data failed
[ 87.832432] sd 6:0:0:0: [sdc] Assuming drive cache: write through
[ 87.866595] sdc: sdc1 sdc2 sdc3
[ 87.898629] sd 6:0:0:0: [sdc] Attached SCSI disk
[ 88.827960] FAT-fs (sdc1): Volume was not properly unmounted. Some data may be corrupt. Please run fsck.
[ 89.016541] hfsplus: write access to a journaled filesystem is not supported, use the force option at your own risk, mounting read-only.
[ 92.629715] usb 4-1: reset SuperSpeed USB device number 2 using xhci_hcd
[ 92.647871] xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep ffff8801fada2f00
[ 92.647875] xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep ffff8801fada2f48
[ 92.866946] sd 6:0:0:0: [sdc] Unhandled error code
[ 92.866950] sd 6:0:0:0: [sdc]
[ 92.866952] Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK
[ 92.866954] sd 6:0:0:0: [sdc] CDB:
[ 92.866955] Read(10): 28 00 00 00 01 d8 00 00 4a 00
[ 92.866962] end_request: I/O error, dev sdc, sector 472
[ 143.153123] xhci_hcd 0000:00:14.0: Command completion event does not match command
[ 143.153156] xhci_hcd 0000:00:14.0: Timeout while waiting for setup device command
[ 148.376995] xhci_hcd 0000:00:14.0: Timeout while waiting for setup device command
[ 148.581217] usb 4-1: device not accepting address 2, error -62
[ 154.385998] xhci_hcd 0000:00:14.0: Command completion event does not match command
[ 154.386040] xhci_hcd 0000:00:14.0: Timeout while waiting for setup device command
[ 159.609793] xhci_hcd 0000:00:14.0: Timeout while waiting for setup device command
[ 159.814136] usb 4-1: device not accepting address 2, error -62
[ 165.618842] xhci_hcd 0000:00:14.0: Command completion event does not match command
[ 165.618899] xhci_hcd 0000:00:14.0: Timeout while waiting for setup device command
[ 170.842626] xhci_hcd 0000:00:14.0: Timeout while waiting for setup device command
[ 171.046926] usb 4-1: device not accepting address 2, error -62
[ 176.851706] xhci_hcd 0000:00:14.0: Command completion event does not match command
[ 176.851749] xhci_hcd 0000:00:14.0: Timeout while waiting for setup device command
[ 182.075515] xhci_hcd 0000:00:14.0: Timeout while waiting for setup device command
[ 182.279805] usb 4-1: device not accepting address 2, error -62
[ 182.280253] sd 6:0:0:0: [sdc] Unhandled error code
[ 182.280265] sd 6:0:0:0: [sdc]
[ 182.280271] Result: hostbyte=DID_TIME_OUT driverbyte=DRIVER_OK
[ 182.280277] sd 6:0:0:0: [sdc] CDB:
[ 182.280280] Read(10): 28 00 00 00 01 d9 00 00 49 00
[ 182.280300] end_request: I/O error, dev sdc, sector 473
[ 182.280364] usb 4-1: USB disconnect, device number 2
[ 182.285970] scsi 6:0:0:0: rejecting I/O to offline device
[ 182.285983] scsi 6:0:0:0: [sdc] killing request
[ 182.286006] scsi 6:0:0:0: [sdc] Unhandled error code
[ 182.286012] scsi 6:0:0:0: [sdc]
[ 182.286018] Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK
[ 182.286024] scsi 6:0:0:0: [sdc] CDB:
[ 182.286028] Read(10): 28 00 00 00 01 d8 00 00 01 00
[ 182.286053] end_request: I/O error, dev sdc, sector 472
[ 182.286089] FAT-fs (sdc1): FAT read failed (blocknr 470)
[ 182.286950] FAT-fs (sdc1): FAT read failed (blocknr 32)
[ 182.287348] FAT-fs (sdc1): FAT read failed (blocknr 32)
[ 182.300059] xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep ffff8801fada2f00
[ 182.300069] xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep ffff8801fada2f48
为了让我能够运行fsck /dev/sdc1
它,它需要以某种方式可用,但事实并非如此。
df -h
这是尝试安装时的输出:
df: ‘/media/cesc/FLAMEL’: Input/output error
Filesystem Size Used Avail Use% Mounted on
udev 3,9G 4,0K 3,9G 1% /dev
tmpfs 789M 1,6M 787M 1% /run
/dev/sda7 20G 15G 3,6G 81% /
none 4,0K 0 4,0K 0% /sys/fs/cgroup
none 5,0M 0 5,0M 0% /run/lock
none 3,9G 672K 3,9G 1% /run/shm
none 100M 12K 100M 1% /run/user
/dev/sda9 166G 45G 113G 29% /home
/dev/sda2 256M 55M 202M 22% /boot/efi
/dev/sdc3 15G 7,6G 6,6G 54% /media/cesc/MAQUIAVELO
/dev/sdc2 266G 49G 217G 19% /media/cesc/PERENELL
/dev/sdc1
没有出现。
如果我尝试fsck /dev/sdc1
我得到:
fsck from util-linux 2.20.1
e2fsck 1.42.9 (4-Feb-2014)
fsck.ext2: No such file or directory while trying to open /dev/sdc1
Possibly non-existent device?
鉴于这种情况,我的问题是:
- 我的磁盘无法修复吗?
- 如果没有,有办法解决吗?
谢谢!
答案1
毫无疑问,你的驱动器要么死了,要么快要死了。
当您运行时它不会出现,df -h
因为它尚未安装。如果当您运行时它没有出现fdisk -l
,或者lsblk
如果您无法fsck
通过磁盘本身运行fsck /dev/sdc
,或者当它连接到不同的端口和/或使用不同的电缆时,则完成。希望您有数据备份。