linux下如何使用两个网络接口

linux下如何使用两个网络接口

我同时有两个或多个网络接口,并且想要使用每个网络通过它发送特殊请求。(我想知道如何使用 iptables 和其他类似的方法来做到这一点)

例如 : 我想观看“network-1”的视频以及我想通过“network-2”发送的其他请求

ifconfig

输出:

enx0c5b8f279a64: flags=4163<UP,BROADCAST,RUNNING,MULTICAST>  mtu 1500
    inet 192.168.8.100  netmask 255.255.255.0  broadcast 192.168.8.255
    inet6 fe80::af19:e5c2:350e:ad09  prefixlen 64  scopeid 0x20<link>
    ether 0c:5b:8f:27:9a:64  txqueuelen 1000  (Ethernet)
    RX packets 74  bytes 16183 (16.1 KB)
    RX errors 0  dropped 0  overruns 0  frame 0
    TX packets 122  bytes 16282 (16.2 KB)
    TX errors 0  dropped 0 overruns 0  carrier 0  collisions 0

lo: flags=73<UP,LOOPBACK,RUNNING>  mtu 65536
    inet 127.0.0.1  netmask 255.0.0.0
    inet6 ::1  prefixlen 128  scopeid 0x10<host>
    loop  txqueuelen 1000  (Local Loopback)
    RX packets 5290686  bytes 3859055101 (3.8 GB)
    RX errors 0  dropped 0  overruns 0  frame 0
    TX packets 5290686  bytes 3859055101 (3.8 GB)
    TX errors 0  dropped 0 overruns 0  carrier 0  collisions 0

ppp0: flags=4305<UP,POINTOPOINT,RUNNING,NOARP,MULTICAST>  mtu 1400
    inet 81.31.179.204  netmask 255.255.255.255  destination 172.17.1.230
    ppp  txqueuelen 3  (Point-to-Point Protocol)
    RX packets 292544  bytes 336720863 (336.7 MB)
    RX errors 0  dropped 0  overruns 0  frame 0
    TX packets 178723  bytes 16928573 (16.9 MB)
    TX errors 0  dropped 0 overruns 0  carrier 0  collisions 0

wlp2s0: flags=4163<UP,BROADCAST,RUNNING,MULTICAST>  mtu 1500
    inet 192.168.1.2  netmask 255.255.255.0  broadcast 192.168.1.255
    inet6 fe80::a71b:2220:7e40:1948  prefixlen 64  scopeid 0x20<link>
    ether e4:70:b8:cf:4f:81  txqueuelen 1000  (Ethernet)
    RX packets 4691632  bytes 4626078058 (4.6 GB)
    RX errors 0  dropped 0  overruns 0  frame 0
    TX packets 4675065  bytes 704065262 (704.0 MB)
    TX errors 0  dropped 0 overruns 0  carrier 0  collisions 0

我的IP路由是

ip route show

输出:

default dev ppp0 proto static scope link metric 50 
default via 192.168.8.1 dev enx0c5b8f279a64 proto dhcp metric 20100 
default via 192.168.1.1 dev wlp2s0 proto dhcp metric 20600 
169.254.0.0/16 dev wlp2s0 scope link metric 1000 
172.17.1.230 via 192.168.1.1 dev wlp2s0 src 192.168.1.2 
172.17.1.230 dev ppp0 proto kernel scope link src 81.31.179.204 metric 50 
172.17.1.230 via 192.168.1.1 dev wlp2s0 proto static metric 600 
192.168.1.0/24 dev wlp2s0 proto kernel scope link src 192.168.1.2 metric 600 
192.168.1.1 dev wlp2s0 proto static scope link metric 600 
192.168.8.0/24 dev enx0c5b8f279a64 proto kernel scope link src 
192.168.8.100 metric 100 

当时我的两个网络接口wlp2s0都是enx0c5b8f279a64

enx0c5b8f279a64我想通过(将通过在代理上设置浏览器来指定)发送一些请求,以及我想通过wlp2s0.

相关内容