使用英特尔 Wireless-AC 9560 配置同时双频 AP

使用英特尔 Wireless-AC 9560 配置同时双频 AP

我有英特尔 NUC 套件 NUC8i7BEH它具有 Intel Wireless-AC 9560 集成无线功能。当我iw在 Linux 上运行时,我得到了该卡的以下输出:

max # scan SSIDs: 20
max scan IEs length: 422 bytes
max # sched scan SSIDs: 20
max # match sets: 11
max # scan plans: 2
max scan plan interval: 65535
max scan plan iterations: 254
Retry short limit: 7
Retry long limit: 4
Coverage class: 0 (up to 0m)
Device supports RSN-IBSS.
Device supports AP-side u-APSD.
Device supports T-DLS.
Supported Ciphers:
    * WEP40 (00-0f-ac:1)
    * WEP104 (00-0f-ac:5)
    * TKIP (00-0f-ac:2)
    * CCMP-128 (00-0f-ac:4)
    * GCMP-128 (00-0f-ac:8)
    * GCMP-256 (00-0f-ac:9)
    * CMAC (00-0f-ac:6)
    * GMAC-128 (00-0f-ac:11)
    * GMAC-256 (00-0f-ac:12)
Available Antennas: TX 0 RX 0
Supported interface modes:
     * IBSS
     * managed
     * AP
     * AP/VLAN
     * monitor
     * P2P-client
     * P2P-GO
     * P2P-device
Band 1:
    Capabilities: 0x19ef
        RX LDPC
        HT20/HT40
        SM Power Save disabled
        RX HT20 SGI
        RX HT40 SGI
        TX STBC
        RX STBC 1-stream
        Max AMSDU length: 7935 bytes
        DSSS/CCK HT40
    Maximum RX AMPDU length 65535 bytes (exponent: 0x003)
    Minimum RX AMPDU time spacing: 4 usec (0x05)
    HT Max RX data rate: 300 Mbps
    HT TX/RX MCS rate indexes supported: 0-15
    Bitrates (non-HT):
        * 1.0 Mbps
        * 2.0 Mbps (short preamble supported)
        * 5.5 Mbps (short preamble supported)
        * 11.0 Mbps (short preamble supported)
        * 6.0 Mbps
        * 9.0 Mbps
        * 12.0 Mbps
        * 18.0 Mbps
        * 24.0 Mbps
        * 36.0 Mbps
        * 48.0 Mbps
        * 54.0 Mbps
    Frequencies:
        * 2412 MHz [1] (22.0 dBm)
        * 2417 MHz [2] (22.0 dBm)
        * 2422 MHz [3] (22.0 dBm)
        * 2427 MHz [4] (22.0 dBm)
        * 2432 MHz [5] (22.0 dBm)
        * 2437 MHz [6] (22.0 dBm)
        * 2442 MHz [7] (22.0 dBm)
        * 2447 MHz [8] (22.0 dBm)
        * 2452 MHz [9] (22.0 dBm)
        * 2457 MHz [10] (22.0 dBm)
        * 2462 MHz [11] (22.0 dBm)
        * 2467 MHz [12] (22.0 dBm)
        * 2472 MHz [13] (22.0 dBm)
        * 2484 MHz [14] (22.0 dBm)
Band 2:
    Capabilities: 0x19ef
        RX LDPC
        HT20/HT40
        SM Power Save disabled
        RX HT20 SGI
        RX HT40 SGI
        TX STBC
        RX STBC 1-stream
        Max AMSDU length: 7935 bytes
        DSSS/CCK HT40
    Maximum RX AMPDU length 65535 bytes (exponent: 0x003)
    Minimum RX AMPDU time spacing: 4 usec (0x05)
    HT Max RX data rate: 300 Mbps
    HT TX/RX MCS rate indexes supported: 0-15
    VHT Capabilities (0x039071f6):
        Max MPDU length: 11454
        Supported Channel Width: 160 MHz
        RX LDPC
        short GI (80 MHz)
        short GI (160/80+80 MHz)
        TX STBC
        SU Beamformee
        MU Beamformee
    VHT RX MCS set:
        1 streams: MCS 0-9
        2 streams: MCS 0-9
        3 streams: not supported
        4 streams: not supported
        5 streams: not supported
        6 streams: not supported
        7 streams: not supported
        8 streams: not supported
    VHT RX highest supported: 0 Mbps
    VHT TX MCS set:
        1 streams: MCS 0-9
        2 streams: MCS 0-9
        3 streams: not supported
        4 streams: not supported
        5 streams: not supported
        6 streams: not supported
        7 streams: not supported
        8 streams: not supported
    VHT TX highest supported: 0 Mbps
    Bitrates (non-HT):
        * 6.0 Mbps
        * 9.0 Mbps
        * 12.0 Mbps
        * 18.0 Mbps
        * 24.0 Mbps
        * 36.0 Mbps
        * 48.0 Mbps
        * 54.0 Mbps
    Frequencies:
        * 5180 MHz [36] (22.0 dBm)
        * 5200 MHz [40] (22.0 dBm)
        * 5220 MHz [44] (22.0 dBm)
        * 5240 MHz [48] (22.0 dBm)
        * 5260 MHz [52] (22.0 dBm)
        * 5280 MHz [56] (22.0 dBm)
        * 5300 MHz [60] (22.0 dBm)
        * 5320 MHz [64] (22.0 dBm)
        * 5340 MHz [68] (22.0 dBm)
        * 5360 MHz [72] (22.0 dBm)
        * 5380 MHz [76] (22.0 dBm)
        * 5400 MHz [80] (22.0 dBm)
        * 5420 MHz [84] (22.0 dBm)
        * 5440 MHz [88] (22.0 dBm)
        * 5460 MHz [92] (22.0 dBm)
        * 5480 MHz [96] (22.0 dBm)
        * 5500 MHz [100] (22.0 dBm)
        * 5520 MHz [104] (22.0 dBm)
        * 5540 MHz [108] (22.0 dBm)
        * 5560 MHz [112] (22.0 dBm)
        * 5580 MHz [116] (22.0 dBm)
        * 5600 MHz [120] (22.0 dBm)
        * 5620 MHz [124] (22.0 dBm)
        * 5640 MHz [128] (22.0 dBm)
        * 5660 MHz [132] (22.0 dBm)
        * 5680 MHz [136] (22.0 dBm)
        * 5700 MHz [140] (22.0 dBm)
        * 5720 MHz [144] (22.0 dBm)
        * 5745 MHz [149] (22.0 dBm)
        * 5765 MHz [153] (22.0 dBm)
        * 5785 MHz [157] (22.0 dBm)
        * 5805 MHz [161] (22.0 dBm)
        * 5825 MHz [165] (22.0 dBm)
        * 5845 MHz [169] (22.0 dBm)
        * 5865 MHz [173] (22.0 dBm)
        * 5885 MHz [177] (22.0 dBm)
        * 5905 MHz [181] (22.0 dBm)
Supported commands:
     * new_interface
     * set_interface
     * new_key
     * start_ap
     * new_station
     * new_mpath
     * set_mesh_config
     * set_bss
     * authenticate
     * associate
     * deauthenticate
     * disassociate
     * join_ibss
     * join_mesh
     * remain_on_channel
     * set_tx_bitrate_mask
     * frame
     * frame_wait_cancel
     * set_wiphy_netns
     * set_channel
     * set_wds_peer
     * tdls_mgmt
     * tdls_oper
     * start_sched_scan
     * probe_client
     * set_noack_map
     * register_beacons
     * start_p2p_device
     * set_mcast_rate
     * connect
     * disconnect
     * channel_switch
     * set_qos_map
     * add_tx_ts
     * set_multicast_to_unicast
Supported TX frame types:
     * IBSS: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
     * managed: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
     * AP: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
     * AP/VLAN: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
     * mesh point: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
     * P2P-client: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
     * P2P-GO: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
     * P2P-device: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
Supported RX frame types:
     * IBSS: 0x40 0xb0 0xc0 0xd0
     * managed: 0x40 0xd0
     * AP: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0
     * AP/VLAN: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0
     * mesh point: 0xb0 0xc0 0xd0
     * P2P-client: 0x40 0xd0
     * P2P-GO: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0
     * P2P-device: 0x40 0xd0
WoWLAN support:
     * wake up on disconnect
     * wake up on magic packet
     * wake up on pattern match, up to 20 patterns of 16-128 bytes,
       maximum packet offset 0 bytes
     * can do GTK rekeying
     * wake up on GTK rekey failure
     * wake up on EAP identity request
     * wake up on 4-way handshake
     * wake up on rfkill release
     * wake up on network detection, up to 11 match sets
     * wake up on TCP connection
software interface modes (can always be added):
     * AP/VLAN
     * monitor
valid interface combinations:
     * #{ managed } <= 1, #{ AP, P2P-client, P2P-GO } <= 1, #{ P2P-device } <= 1,
       total <= 3, #channels <= 2
HT Capability overrides:
     * MCS: ff ff ff ff ff ff ff ff ff ff
     * maximum A-MSDU length
     * supported channel width
     * short GI for 40 MHz
     * max A-MPDU length exponent
     * min MPDU start spacing
Device supports TX status socket option.
Device supports HT-IBSS.
Device supports SAE with AUTHENTICATE command
Device supports low priority scan.
Device supports scan flush.
Device supports per-vif TX power setting
P2P GO supports CT window setting
P2P GO supports opportunistic powersave setting
Driver supports full state transitions for AP/GO clients
Driver supports a userspace MPM
Driver/device bandwidth changes during BSS lifetime (AP/GO mode)
Device adds DS IE to probe requests
Device can update TPC Report IE
Device supports static SMPS
Device supports dynamic SMPS
Device supports WMM-AC admission (TSPECs)
Device supports configuring vdev MAC-addr on create.
Device supports TDLS channel switching

对我来说,它似乎有两个频段,但我不清楚它是否支持同时双频,以及如何在 Linux 上将其配置为双频 AP(我目前正在使用 Ubuntu,但可以是任何 Linux)?

相关内容