上传速度慢(CentOS 6)

上传速度慢(CentOS 6)

过去一周,我的服务器上传速度一直很慢。第一次出现这种情况时,重启网络服务可以解决速度慢的问题。之后,速度会在 24 到 72 小时内保持正常,然后再次变慢。今天,当我重启网络服务时,服务器挂了,我不得不手动重启服务器。

我运行的是 CentOS 6.5,带有最新的 OpenVZ 内核,因为该服务器用于托管 vps 服务器。如果我需要提供任何其他信息,请告诉我。我拥有该公司其他配置基本相同的服务器,这是唯一遇到此问题的服务器。该公司保证 100MB/s。当速度变慢时,我尝试从服务器下载测试文件时,速度约为 20 kb/s。

ethtool:

Settings for eth0:
        Supported ports: [ TP ]
        Supported link modes:   10baseT/Half 10baseT/Full
                                100baseT/Half 100baseT/Full
                                1000baseT/Full
        Supported pause frame use: No
        Supports auto-negotiation: Yes
        Advertised link modes:  10baseT/Half 10baseT/Full
                                100baseT/Half 100baseT/Full
                                1000baseT/Full
        Advertised pause frame use: No
        Advertised auto-negotiation: Yes
        Speed: 100Mb/s
        Duplex: Full
        Port: Twisted Pair
        PHYAD: 2
        Transceiver: internal
        Auto-negotiation: on
        MDI-X: on
        Supports Wake-on: pumbg
        Wake-on: g
        Current message level: 0x00000007 (7)
                               drv probe link
        Link detected: yes

dmesg |grep e1000e

    [    2.204393] e1000e: Intel(R) PRO/1000 Network Driver - 2.3.2-k
[    2.204395] e1000e: Copyright(c) 1999 - 2013 Intel Corporation.
[    2.204417] e1000e 0000:00:19.0: PCI INT A -> GSI 20 (level, low) -> IRQ 20
[    2.204422] e1000e 0000:00:19.0: setting latency timer to 64
[    2.204503] e1000e 0000:00:19.0: Interrupt Throttling Rate (ints/sec) set to dynamic conservative mode
[    2.204531] e1000e 0000:00:19.0: irq 69 for MSI/MSI-X
[    2.404296] e1000e 0000:00:19.0: eth0: registered PHC clock
[    2.404299] e1000e 0000:00:19.0: eth0: (PCI Express:2.5GT/s:Width x1) f8:b1:56:b8:96:fe
[    2.404300] e1000e 0000:00:19.0: eth0: Intel(R) PRO/1000 Network Connection
[    2.404327] e1000e 0000:00:19.0: eth0: MAC: 10, PHY: 11, PBA No: 5041FF-0FF
[    3.619389] e1000e 0000:00:19.0: irq 69 for MSI/MSI-X
[    3.720105] e1000e 0000:00:19.0: irq 69 for MSI/MSI-X
[    5.249001] e1000e: eth0 NIC Link is Up 100 Mbps Full Duplex, Flow Control: None
[    5.249010] e1000e 0000:00:19.0: eth0: 10/100 speed: disabling TSO
[  299.993906] e1000e: eth0 NIC Link is Down
[  301.777634] e1000e: eth0 NIC Link is Up 100 Mbps Full Duplex, Flow Control: None
[  301.777639] e1000e 0000:00:19.0: eth0: 10/100 speed: disabling TSO
[  301.789655] e1000e: eth0 NIC Link is Down
[  303.640797] e1000e: eth0 NIC Link is Up 100 Mbps Full Duplex, Flow Control: None
[  303.640802] e1000e 0000:00:19.0: eth0: 10/100 speed: disabling TSO
[  312.563531] e1000e: eth0 NIC Link is Down
[  314.248255] e1000e: eth0 NIC Link is Up 100 Mbps Full Duplex, Flow Control: None
[  314.248260] e1000e 0000:00:19.0: eth0: 10/100 speed: disabling TSO
[  368.737532] e1000e: eth0 NIC Link is Down
[  370.470445] e1000e: eth0 NIC Link is Up 100 Mbps Full Duplex, Flow Control: None
[  370.470449] e1000e 0000:00:19.0: eth0: 10/100 speed: disabling TSO
[  370.871902] e1000e: eth0 NIC Link is Down
[  372.566629] e1000e: eth0 NIC Link is Up 100 Mbps Full Duplex, Flow Control: None
[  372.566633] e1000e 0000:00:19.0: eth0: 10/100 speed: disabling TSO
[  372.650533] e1000e: eth0 NIC Link is Down
[  374.402633] e1000e: eth0 NIC Link is Up 100 Mbps Full Duplex, Flow Control: None
[  374.402638] e1000e 0000:00:19.0: eth0: 10/100 speed: disabling TSO
[91265.671501] e1000e 0000:00:19.0: irq 69 for MSI/MSI-X
[91265.772193] e1000e 0000:00:19.0: irq 69 for MSI/MSI-X
[91269.900310] e1000e: eth0 NIC Link is Up 100 Mbps Full Duplex, Flow Control: None
[91269.900320] e1000e 0000:00:19.0: eth0: 10/100 speed: disabling TSO
[91298.315872] e1000e: eth0 NIC Link is Down
[91300.049356] e1000e: eth0 NIC Link is Up 100 Mbps Full Duplex, Flow Control: None
[91300.049373] e1000e 0000:00:19.0: eth0: 10/100 speed: disabling TSO
[91312.163795] e1000e: eth0 NIC Link is Down
[91313.835394] e1000e: eth0 NIC Link is Up 100 Mbps Full Duplex, Flow Control: None
[91313.835397] e1000e 0000:00:19.0: eth0: 10/100 speed: disabling TSO
[91315.412871] e1000e: eth0 NIC Link is Down
[91317.218629] e1000e: eth0 NIC Link is Up 100 Mbps Full Duplex, Flow Control: None
[91317.218641] e1000e 0000:00:19.0: eth0: 10/100 speed: disabling TSO
[91449.457109] e1000e 0000:00:19.0: irq 69 for MSI/MSI-X
[91449.557589] e1000e 0000:00:19.0: irq 69 for MSI/MSI-X
[91451.105209] e1000e: eth0 NIC Link is Up 100 Mbps Full Duplex, Flow Control: None
[91451.105213] e1000e 0000:00:19.0: eth0: 10/100 speed: disabling TSO
[91451.191593] e1000e: eth0 NIC Link is Down
[91452.905469] e1000e: eth0 NIC Link is Up 100 Mbps Full Duplex, Flow Control: None
[91452.905475] e1000e 0000:00:19.0: eth0: 10/100 speed: disabling TSO
[91454.344927] e1000e: eth0 NIC Link is Down
[91456.040457] e1000e: eth0 NIC Link is Up 100 Mbps Full Duplex, Flow Control: None
[91456.040465] e1000e 0000:00:19.0: eth0: 10/100 speed: disabling TSO

网络状态

Kernel Interface table
Iface       MTU Met    RX-OK RX-ERR RX-DRP RX-OVR    TX-OK TX-ERR TX-DRP TX-OVR Flg
eth0       1500   0 11192854     21      0      0 10035615      0      0      0 BMRU
lo        16436   0        1      0      0      0        1      0      0      0 LRU
venet0     1500   0  9972546      0      0      0 10747306      0      1      0 BOPRU

ifconfig eth0

eth0      Link encap:Ethernet  HWaddr F8:B1:56:B8:96:FE
          inet addr:xxxxxxxxxx  Bcast:xxxxxxxxxx  Mask:xxxxxxxxxx
          inet6 addr: xxxxxxxxxx/64 Scope:Link
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:11200159 errors:21 dropped:0 overruns:0 frame:11
          TX packets:10043059 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:6744462142 (6.2 GiB)  TX bytes:4788632826 (4.4 GiB)
          Interrupt:20 Memory:fbf00000-fbf20000

答案1

您没有提供太多有关dmesg时间的信息,但如果这是在刚启动时立即开始出现问题的,那么您的问题就是交换机端口出现抖动,这可能是由任何原因(您的驱动程序、硬件、电缆、交换机的硬件或交换机的配置)引起的。鉴于您说这是由一家“公司”托管的,任何一家托管公司的支持部门都应该至少将这个问题排除在考虑范围之外,除了您的驱动程序之外,其他所有原因都不是罪魁祸首(例如,插入并使用备用硬件进行测试)。托管公司(如黑网或者Rackspace) 将全面处理整个问题。

相关内容