Ubuntu 14.04 上的 3G 调制解调器

Ubuntu 14.04 上的 3G 调制解调器

我的两个 3G 调制解调器(未知(见本表)在 Ubuntu 14.04 上不起作用。我尝试将 SIM 卡插入笔记本电脑 Dell D630 的 3G 插槽,也尝试使用外部 3G 调制解调器卡。结果:我可以创建宽带网络,但创建后此网络不可用。重新启动服务网络管理器也不起作用。

/etc/wvdial.conf是空的。

lsusb:

总线 002 设备 003:ID 1b1c:1a03 Corsair
总线 003 设备 002:ID 413c:8140 Dell Computer Corp. 无线 360 蓝牙
总线 005 设备 002:ID 04f3:02f4 义隆电子股份有限公司 2.4G 无线鼠标
总线 007 设备 002:ID 0b97:7761 O2 Micro, Inc. Oz776 1.1 集线器
总线 007 设备 003:ID 0483:2016 SGS 汤姆森微电子指纹读取器
总线 001 设备 001:ID 1d6b:0002 Linux Foundation 2.0 根集线器
总线 002 设备 001:ID 1d6b:0002 Linux Foundation 2.0 根集线器
总线 003 设备 001:ID 1d6b:0001 Linux Foundation 1.1 根集线器
总线 004 设备 001:ID 1d6b:0001 Linux Foundation 1.1 根集线器
总线 005 设备 001:ID 1d6b:0001 Linux Foundation 1.1 根集线器
总线 006 设备 001:ID 1d6b:0001 Linux Foundation 1.1 根集线器
总线 007 设备 001:ID 1d6b:0001 Linux Foundation 1.1 根集线器
总线 007 设备 004:ID 0b97:7772 O2 Micro, Inc. OZ776 CCID 智能卡读卡器
 

lshal:

udi = '/org/freedesktop/Hal/devices/usb_device_b97_7772_noserial'
  info.linux.driver ='usb'(字符串)
  info.parent = '/org/freedesktop/Hal/devices/usb_device_b97_7761_noserial' (字符串)
  info.product = 'OZ776 CCID 智能卡读卡器' (字符串)
  信息.子系统 = 'usb_device' (字符串)
  info.udi = '/org/freedesktop/Hal/devices/usb_device_b97_7772_noserial' (字符串)
  info.vendor = 'O2 Micro, Inc.' (字符串)
  linux.device_file = '/dev/bus/usb/007/004' (字符串)
  linux.hotplug_type = 2 (0x2) (int)
  linux.subsystem ='usb'(字符串)
  linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:1d.2/usb7/7-1/7-1.2' (字符串)
  usb_device.bus_number = 7 (0x7) (int)
  usb_device.can_wake_up = true (布尔值)
  usb_device.configuration_value = 1 (0x1) (int)
  usb_device.device_class = 0 (0x0) (int)
  usb_device.device_protocol = 0 (0x0) (int)
  usb_device.device_revision_bcd = 272 (0x110) (int)
  usb_device.device_subclass = 0 (0x0) (int)
  usb_device.is_self_powered = true (布尔值)
  usb_device.linux.device_number = 4 (0x4) (int)
  usb_device.linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:1d.2/usb7/7-1/7-1.2' (字符串)
  usb_device.max_power = 0 (0x0) (int)
  usb_device.num_configurations = 1 (0x1) (int)
  usb_device.num_interfaces = 1 (0x1) (int)
  usb_device.num_ports = 0 (0x0) (int)
  usb_device.product = 'OZ776 CCID 智能卡读卡器' (字符串)
  usb_device.product_id = 30578 (0x7772) (int)
  usb_device.speed = 12.0 (12) (双精度)
  usb_device.vendor = 'O2 Micro, Inc.' (字符串)
  usb_device.vendor_id = 2967 (0xb97) (int)
  usb_device.version = 1.1 (1.1) (双精度)


udi = '/org/freedesktop/Hal/devices/usb_device_b97_7761_noserial'
  info.linux.driver ='usb'(字符串)
  info.parent = '/org/freedesktop/Hal/devices/usb_device_1d6b_1_0000_00_1d_2' (字符串)
  info.product = 'Oz776 1.1 Hub' (字符串)
  信息.子系统 = 'usb_device' (字符串)
  info.udi = '/org/freedesktop/Hal/devices/usb_device_b97_7761_noserial' (字符串)
  info.vendor = 'O2 Micro, Inc.' (字符串)
  linux.device_file = '/dev/bus/usb/007/002' (字符串)
  linux.hotplug_type = 2 (0x2) (int)
  linux.subsystem ='usb'(字符串)
  linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:1d.2/usb7/7-1' (字符串)
  usb_device.bus_number = 7 (0x7) (int)
  usb_device.can_wake_up = true (布尔值)
  usb_device.configuration_value = 1 (0x1) (int)
  usb_device.device_class = 9 (0x9) (int)
  usb_device.device_protocol = 0 (0x0) (int)
  usb_device.device_revision_bcd = 272 (0x110) (int)
  usb_device.device_subclass = 0 (0x0) (int)
  usb_device.is_self_powered = true (布尔值)
  usb_device.linux.device_number = 2 (0x2) (int)
  usb_device.linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:1d.2/usb7/7-1' (字符串)
  usb_device.max_power = 2 (0x2) (int)
  usb_device.num_configurations = 1 (0x1) (int)
  usb_device.num_interfaces = 1 (0x1) (int)
  usb_device.num_ports = 4 (0x4) (int)
  usb_device.product ='Oz776 1.1 Hub'(字符串)
  usb_device.product_id = 30561 (0x7761) (int)
  usb_device.speed = 12.0 (12) (双精度)
  usb_device.vendor = 'O2 Micro, Inc.' (字符串)
  usb_device.vendor_id = 2967 (0xb97) (int)
  usb_device.version = 1.1 (1.1) (双精度)

udi = '/org/freedesktop/Hal/devices/usb_device_b97_7761_noserial_if0'
  info.linux.driver ='hub'(字符串)
  info.parent = '/org/freedesktop/Hal/devices/usb_device_b97_7761_noserial' (字符串)
  info.product ='USB 集线器接口'(字符串)
  信息.子系统 = 'usb' (字符串)
  info.udi = '/org/freedesktop/Hal/devices/usb_device_b97_7761_noserial_if0' (字符串)
  linux.hotplug_type = 2 (0x2) (int)
  linux.subsystem ='usb'(字符串)
  linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:1d.2/usb7/7-1/7-1:1.0' (字符串)
  usb.bus_number = 7 (0x7) (int)
  usb.can_wake_up = true (布尔值)
  usb.configuration_value = 1 (0x1) (int)
  usb.device_class = 9 (0x9) (int)
  usb.device_protocol = 0 (0x0) (int)
  usb.device_revision_bcd = 272 (0x110) (int)
  usb.device_subclass = 0 (0x0) (int)
  usb.interface.class = 9 (0x9) (int)
  usb.接口.编号 = 0 (0x0) (int)
  usb.interface.protocol = 0 (0x0) (int)
  usb.interface.subclass = 0 (0x0) (int)
  usb.is_self_powered = true (布尔值)
  usb.linux.device_number = 2 (0x2) (int)
  usb.linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:1d.2/usb7/7-1/7-1:1.0' (字符串)
  usb.max_power = 2 (0x2) (int)
  usb.num_configurations = 1 (0x1) (int)
  usb.num_interfaces = 1 (0x1) (int)
  usb.num_ports = 4 (0x4) (int)
  usb.product ='USB 集线器接口'(字符串)
  usb.product_id = 30561 (0x7761) (int)
  usb.speed = 12.0 (12) (双精度)
  usb.vendor = 'O2 Micro, Inc.' (字符串)
  usb.vendor_id = 2967 (0xb97) (int)
  usb.version = 1.1 (1.1) (双精度)

udi = '/org/freedesktop/Hal/devices/usb_device_b97_7772_noserial'
  info.linux.driver ='usb'(字符串)
  info.parent = '/org/freedesktop/Hal/devices/usb_device_b97_7761_noserial' (字符串)
  info.product = 'OZ776 CCID 智能卡读卡器' (字符串)
  信息.子系统 = 'usb_device' (字符串)
  info.udi = '/org/freedesktop/Hal/devices/usb_device_b97_7772_noserial' (字符串)
  info.vendor = 'O2 Micro, Inc.' (字符串)
  linux.device_file = '/dev/bus/usb/007/004' (字符串)
  linux.hotplug_type = 2 (0x2) (int)
  linux.subsystem ='usb'(字符串)
  linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:1d.2/usb7/7-1/7-1.2' (字符串)
  usb_device.bus_number = 7 (0x7) (int)
  usb_device.can_wake_up = true (布尔值)
  usb_device.configuration_value = 1 (0x1) (int)
  usb_device.device_class = 0 (0x0) (int)
  usb_device.device_protocol = 0 (0x0) (int)
  usb_device.device_revision_bcd = 272 (0x110) (int)
  usb_device.device_subclass = 0 (0x0) (int)
  usb_device.is_self_powered = true (布尔值)
  usb_device.linux.device_number = 4 (0x4) (int)
  usb_device.linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:1d.2/usb7/7-1/7-1.2' (字符串)
  usb_device.max_power = 0 (0x0) (int)
  usb_device.num_configurations = 1 (0x1) (int)
  usb_device.num_interfaces = 1 (0x1) (int)
  usb_device.num_ports = 0 (0x0) (int)
  usb_device.product = 'OZ776 CCID 智能卡读卡器' (字符串)
  usb_device.product_id = 30578 (0x7772) (int)
  usb_device.speed = 12.0 (12) (双精度)
  usb_device.vendor = 'O2 Micro, Inc.' (字符串)
  usb_device.vendor_id = 2967 (0xb97) (int)
  usb_device.version = 1.1 (1.1) (双精度)

集成调制解调器是:

Dell Wireless 5520 移动宽带(三频 HSDPA 3.6)迷你卡,支持 AT&T(美国)和
沃达丰(部分欧洲国家)Dell Wireless 5720 移动宽带
(EVDO Rev A)迷你卡,支持 Verizon Wireless(美国)、Sprint(美国)和 Telus(加拿大)服务

外部是:T-Mobile ip wireless ue pcmmcia v3 tx

答案1

这是一个管理 3g 连接的程序,请下载它并将其保存到您的主文件夹,不要重命名它。

你需要这个

sudo apt-get install qt-sdk

它是500mb,所以确保你有足够的3g

一旦完成,一次运行一行

tar xzvf umtsmon-0.9.i386.tar.gz
cd umtsmon-0.9
qmake
make clean all
lrelease umtsmon.pro

这将安装它,在仪表板中找到 umtsmon。

我还发现了一些事情http://ubuntuforums.org/showthread.php?t=787777

我在网上到处搜索,没有找到任何信息,只能自己想办法解决。既然找不到任何东西,我决定分享我的经验,希望能帮助到别人。

这是我在戴尔 d630 上做的下载并安装betavine 沃达丰 Linux 驱动程序

然后在终端

"sudo lsusb -v | less"

查看设备,它是一个很长的列表,向下滚动直到找到内部卡,我的看起来像这样:

Bus 002 Device 003: ID 413c:8137 Dell Computer Corp. 
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 1.10
bDeviceClass 0 (Defined at Interface level)
bDeviceSubClass 0 
bDeviceProtocol 0 
bMaxPacketSize0 64
idVendor 0x413c Dell Computer Corp.
idProduct 0x8137 
bcdDevice 0.00
iManufacturer 1 Novatel Wireless
iProduct 2 Novatel Wireless HSDPA Modem
iSerial 2 Novatel Wireless HSDPA Modem
bNumConfigurations 1
Configuration Descriptor:
bLength 9

完成后,记下 id 供应商和 id 产品值。

在终端中输入

sudo modprobe usbserial vendor=0x413c product=0x8115

在您之前记下的供应商和产品字段中插入您自己的 idproduct 和 idvendor 编号

然后

`grep tty /var/log/messages` 

并检查输出是否表明调制解调器已连接到 ttyUSB1 0r ttyUSB0

现在启动适用于 Linux 的 Vodafone 驱动程序

当显示设备设置时,在下拉列表中选择串行,并在两个输入字段中选择 typtttyUSB0ttyUSB1取决于调制解调器的连接位置,即查看输出

grep tty /var/log/messages

我希望有人觉得这篇文章很有价值,并且我为一些人节省了数小时的沮丧时间。

平安!

还有一件事要确保设备在启动时激活:

"sudo gedit /etc/modules"

添加到文件末尾

echo usbserial vendor=0x4XXX product=0x81XX

(X = 您的特定供应商和产品 ID)

相关内容