我购买了 TP-Link Archer T2UH AC600 无线适配器，我已经能够很好地编译驱动程序，但我现在面临的问题是文件RT2870STA.dat。我试图从 TP-Link 为 Linux 机器提供的手册中进行指导，但我对如何处理空字段感到困惑，并且大多数字段我不明白它们的含义。
Default
CountryRegion=5
CountryRegionABand=7
CountryCode=CA
SSID=Rogers343 <--#nomyreal SSID
NetworkType=Infra
WirelessMode=9
Channel=0
BeaconPeriod=100
TxPower=100
BGProtection=0
TxPreamble=0
RTSThreshold=2347
FragThreshold=2346
TxBurst=1
WmmCapable=0
AckPolicy=0;0;0;0
AuthMode=WPA2PSK
EncrypType=NONE
WPAPSK=1234567
DefaultKeyID=1
Key1Type=0
Key1Str=
Key2Type=0
Key2Str=
Key3Type=0
Key3Str=
Key4Type=0
Key4Str=
PSMode=CAM
FastRoaming=0
RoamThreshold=70
HT_RDG=1
HT_EXTCHA=0
HT_OpMode=1
HT_MpduDensity=4
HT_BW=1
HT_AutoBA=1
HT_BADecline=0
HT_AMSDU=0
HT_BAWinSize=64
HT_GI=1
HT_MCS=33
HT_MIMOPSMode=3
EthConvertMode=
EthCloneMac=
IEEE80211H=0
TGnWifiTest=0
WirelessEvent=0
MeshId=MESH
MeshAutoLink=1
MeshAuthMode=OPEN
MeshEncrypType=NONE
MeshWPAKEY=
MeshDefaultkey=1
MeshWEPKEY=
CarrierDetect=0
有一些空字段，我不知道那里有什么样的值。我知道将 更改SSID为我的 wifi 连接的名称。我不太确定CountryCode我在加拿大有什么价值，AuthMode我认为我应该输入WPA&WPA2Personal因为那是我当前使用的 wifi 连接。文件中EncrypType自动没有任何内容，我不确定它的用途，并且WPAPSK将是我的密码。还有很多其他空字段，我不知道如何处理它们。因为我正在尝试使用 iwpriv 在 Kali Linux 中设置无线适配器，并且配置需要我转到RT2870STA.dat才能/etc/Wireless/RT2870STA/RT2870STA.dat继续。另外，为了让我能够使用 dhclient 请求 IP，我需要配置接入点的 SSID。我的问题是如何获取 AP 的 SSID？如果我将 wlan0 接口的值与 ra0 接口的值进行比较，则 wlan0 接入点看起来像一个 MAC 地址，但我在适配器上看不到 MAC 地址，而且我不知道要在其中输入什么值。以下是我设置适配器所采取的步骤iwpriv
iwpriv ra0 set NetworkType=Infra
iwpriv ra0 set AuthMode=WPA2PSK
iwpriv ra0 set EncrypType=TKIP
iwpriv ra0 set SSID="Rogers343"
iwpriv ra0 set WPAPSK=1234567 <-- not my acutal pswd
iwpriv ra0 set WirelessMode=14
输入这些命令后，iwconfig ra0显示的内容如下
Ralink STA ESSID:"Rogers343" Nickname:"MT7610U_STA"
Mode:Auto Frequency=5.18 GHz Access Point: Not-Associated
Bit Rate:1 Mb/s
RTS thr:off Fragment thr:off
Encryption key:off
Link Quality=10/100 Signal level:0 dBm Noise level:0 dBm
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:0 Missed beacon:0
dmesg插入适配器时的输出 。
3539.786506] usb 1-1.3: new high-speed USB device number 8 using ehci-pci
[ 3539.910506] usb 1-1.3: New USB device found, idVendor=148f, idProduct=761a
[ 3539.910508] usb 1-1.3: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 3539.910509] usb 1-1.3: Product: WiFi
[ 3539.910510] usb 1-1.3: Manufacturer: MediaTek
[ 3539.910511] usb 1-1.3: SerialNumber: 1.0
[ 3539.911075]
=== pAd = ffffc64740b25000, size = 892576 ===
[ 3539.911171] <-- RTMPAllocTxRxRingMemory, Status=0
[ 3539.911300] <-- RTMPAllocAdapterBlock, Status=0
[ 3539.911493] ==>RT65xx_WLAN_ChipOnOff(): OnOff:1, Reset= 0, pAd->WlanFunCtrl:0x0, Reg-WlanFunCtrl=0xff000002
[ 3539.912593] MCUType = 2
[ 3539.912869] NVM is EFUSE
[ 3539.912870] Endpoint(8) is for In-band Command
[ 3539.912871] Endpoint(4) is for WMM0 AC0
[ 3539.912871] Endpoint(5) is for WMM0 AC1
[ 3539.912872] Endpoint(6) is for WMM0 AC2
[ 3539.912872] Endpoint(7) is for WMM0 AC3
[ 3539.912873] Endpoint(9) is for WMM1 AC0
[ 3539.912874] Endpoint(84) is for Data-In
[ 3539.912874] Endpoint(85) is for Command Rsp
[ 3632.642059] -->RTUSBVenderReset
[ 3632.642162] <--RTUSBVenderReset
[ 3632.647128] fw version:0.1.00 build:7640
[ 3632.647130] build time:201308221655____
[ 3632.647135] ilm length = 68780(bytes)
[ 3632.647136] dlm length = 11476(bytes)
[ 3632.729684] #
[ 3632.736655] loading fw......
[ 3632.857890] #
[ 3633.074167] RTMP_TimerListAdd: add timer obj ffffc64740ba61e0!
[ 3633.074169] RTMP_TimerListAdd: add timer obj ffffc64740ba6250!
[ 3633.074177] RTMP_TimerListAdd: add timer obj ffffc64740b38c38!
[ 3633.074178] RTMP_TimerListAdd: add timer obj ffffc64740b38e18!
[ 3633.086233] cfg_mode=5
[ 3633.086236] wmode_band_equal(): Band Not Equal!
[ 3633.086350] Key1Str is Invalid key length(0) or Type(0)
[ 3633.086361] Key2Str is Invalid key length(0) or Type(0)
[ 3633.086372] Key3Str is Invalid key length(0) or Type(0)
[ 3633.086383] Key4Str is Invalid key length(0) or Type(0)
[ 3633.086687] 1. Phy Mode = 31
[ 3633.086688] 2. Phy Mode = 31
[ 3633.086690] NVM is Efuse and its size =1d[1e0-1fc]
[ 3633.097715] /root/src/mt7610u_wifi_sta_v3002_dpo_20130916/os/linux/../../chips/mt76x0.c:2114 assert (pAd->TxPower[choffset].Channel == 36)failed
[ 3633.111176] ERROR!!! E2PROM: WRONG VERSION 0x2, should be 1
[ 3633.115302] mt76x0_read_tx_alc_info_from_eeprom: EEPROM_MT76x0_TEMPERATURE_OFFSET (0xD1) = 0xf8
[ 3633.115303] mt76x0_read_tx_alc_info_from_eeprom: TemperatureOffset = 0xfffffff8
[ 3633.115303] Temperature Tx ALC not enabled
[ 3633.130303] 3. Phy Mode = 31
[ 3633.130305] AntCfgInit: primary/secondary ant 0/1
[ 3633.138969] RTMPSetPhyMode: channel is out of range, use first channel=1
[ 3633.140555] MCS Set = ff 00 00 00 01
[ 3633.150491] <==== rt28xx_init, Status=0
[ 3633.151431] 0x1300 = 00064300
[ 3633.151432] RTMPDrvSTAOpen(1):Check if PDMA is idle!
[ 3633.151556] RTMPDrvSTAOpen(2):Check if PDMA is idle!
[ 4260.799872] receive cmd msg fail(-71)
[ 4260.799965] Bulk In Failed. Status=-71, BIIdx=0x0, BIRIdx=0x0, actual_length= 0x0
[ 4260.804373] receive cmd msg fail(-71)
[ 4260.832271] #
[ 4260.834242] receive cmd msg fail(-71)
[ 4260.838494] receive cmd msg fail(-71)
[ 4260.841272] #
[ 4260.842743] receive cmd msg fail(-71)
[ 4260.846994] receive cmd msg fail(-71)
[ 4260.850247] #
[ 4260.851243] receive cmd msg fail(-71)
[ 4260.855520] receive cmd msg fail(-71)
[ 4260.859274] #
[ 4260.996257] receive cmd msg fail(-71)
[ 4260.998887] #
[ 4261.000507] receive cmd msg fail(-71)
[ 4261.003855] RTUSB_VendorRequest failed(-71),TxFlags=0x0, ReqType=IN, Req=0x7, Idx=0x1000,pAd->Flags=0x31080002
[ 4261.004758] receive cmd msg fail(-71)
[ 4261.007759] Bulk In Failed. Status=-71, BIIdx=0x0, BIRIdx=0x0, actual_length= 0x0
[ 4261.009009] receive cmd msg fail(-71)
[ 4261.030639] #
[ 4261.034139] usb 1-1.3: USB disconnect, device number 8
[ 4261.034509] receive cmd msg fail(-108)
[ 4261.034511] usb_rx_cmd_msg_complete:submit urb fail(-19)
[ 4261.034517] usb_rx_cmd_msg_submit:submit urb fail(-19)
[ 4261.034519] rtusb_disconnect: unregister usbnet usb-0000:00:1d.0-1.3
[ 4261.034522] RtmpOSNetDevDetach(): RtmpOSNetDeviceDetach(), dev->name=ra0!
[ 4261.035606] #
[ 4261.035608] RTUSB_VendorRequest failed(-19),TxFlags=0x0, ReqType=IN, Req=0x7, Idx=0x1000,pAd->Flags=0x31080542
[ 4261.035609] CMDTHREAD_RESET_BULK_IN: Cannot do bulk in because flags(0x31080542) on !
[ 4261.049617] WIFI device has been disconnected
[ 4261.049668] WIFI device has been disconnected
[ 4261.049668] WIFI device has been disconnected
[ 4261.049669] WIFI device has been disconnected
[ 4261.049673] tx_kickout_fail_count = 0
[ 4261.049673] tx_timeout_fail_count = 0
[ 4261.049674] rx_receive_fail_count = 58
[ 4261.049674] alloc_cmd_msg = 7672
[ 4261.049675] free_cmd_msg = 7672
[ 4261.132674] WIFI device has been disconnected
[ 4261.132677] ==>RT65xx_WLAN_ChipOnOff(): OnOff:0, Reset= 0, pAd->WlanFunCtrl:0xff000003, Reg-WlanFunCtrl=0xffffffff
[ 4261.132677] WIFI device has been disconnected
[ 4261.132678] VendrCmdMultiWrite_nBytes failed!
[ 4261.132698] WIFI device has been disconnected
[ 4261.132708] ---> RTMPFreeTxRxRingMemory
[ 4261.132722] <--- RTMPFreeTxRxRingMemory
[ 4261.132759] RTUSB disconnect successfully
[ 4981.190839] usb 1-1.3: new high-speed USB device number 9 using ehci-pci
[ 4981.315282] usb 1-1.3: New USB device found, idVendor=148f, idProduct=761a
[ 4981.315284] usb 1-1.3: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 4981.315285] usb 1-1.3: Product: WiFi
[ 4981.315286] usb 1-1.3: Manufacturer: MediaTek
[ 4981.315287] usb 1-1.3: SerialNumber: 1.0
[ 4981.315819]
=== pAd = ffffc64740b25000, size = 892576 ===
[ 4981.315904] <-- RTMPAllocTxRxRingMemory, Status=0
[ 4981.316006] <-- RTMPAllocAdapterBlock, Status=0
[ 4981.316133] ==>RT65xx_WLAN_ChipOnOff(): OnOff:1, Reset= 0, pAd->WlanFunCtrl:0x0, Reg-WlanFunCtrl=0xff000002
[ 4981.317259] MCUType = 2
[ 4981.317507] NVM is EFUSE
[ 4981.317508] Endpoint(8) is for In-band Command
[ 4981.317509] Endpoint(4) is for WMM0 AC0
[ 4981.317509] Endpoint(5) is for WMM0 AC1
[ 4981.317510] Endpoint(6) is for WMM0 AC2
[ 4981.317511] Endpoint(7) is for WMM0 AC3
[ 4981.317511] Endpoint(9) is for WMM1 AC0
[ 4981.317512] Endpoint(84) is for Data-In
[ 4981.317512] Endpoint(85) is for Command Rsp
然后我这样做了systemctl restart network-manager.service
，此时我被踢出了我的网络，但我可以看到两个 wifi 图标都出现在网络管理器中，但两张卡都显示“不可用”，如下图所示，并且没有网络被拾取。
dmesg这是发生这种情况后 的输出
238.916761] bluetooth hci0: firmware: failed to load brcm/BCM.hcd (-2)
[ 238.916766] bluetooth hci0: Direct firmware load for brcm/BCM.hcd failed with error -2
[ 238.916769] Bluetooth: hci0: BCM: Patch brcm/BCM.hcd not found
[ 239.115808] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 239.310935] r8169 0000:07:00.0 eth0: link down
[ 239.310991] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 239.311865] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 240.719041] atkbd serio0: Unknown key pressed (translated set 2, code 0x8d on isa0060/serio0).
[ 240.719043] atkbd serio0: Use 'setkeycodes e00d <keycode>' to make it known.
[ 285.069677] ERROR @wl_notify_scan_status : wlan0 Scan_results error (-22)
[ 954.235212] perf: interrupt took too long (2506 > 2500), lowering kernel.perf_event_max_sample_rate to 79750
[ 1193.231540] perf: interrupt took too long (3135 > 3132), lowering kernel.perf_event_max_sample_rate to 63750
[ 1470.857282] perf: interrupt took too long (4013 > 3918), lowering kernel.perf_event_max_sample_rate to 49750
[ 2345.359889] perf: interrupt took too long (5032 > 5016), lowering kernel.perf_event_max_sample_rate to 39500
[ 3539.786506] usb 1-1.3: new high-speed USB device number 8 using ehci-pci
[ 3539.910506] usb 1-1.3: New USB device found, idVendor=148f, idProduct=761a
[ 3539.910508] usb 1-1.3: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 3539.910509] usb 1-1.3: Product: WiFi
[ 3539.910510] usb 1-1.3: Manufacturer: MediaTek
[ 3539.910511] usb 1-1.3: SerialNumber: 1.0
[ 3539.911075]
=== pAd = ffffc64740b25000, size = 892576 ===
[ 3539.911171] <-- RTMPAllocTxRxRingMemory, Status=0
[ 3539.911300] <-- RTMPAllocAdapterBlock, Status=0
[ 3539.911493] ==>RT65xx_WLAN_ChipOnOff(): OnOff:1, Reset= 0, pAd->WlanFunCtrl:0x0, Reg-WlanFunCtrl=0xff000002
[ 3539.912593] MCUType = 2
[ 3539.912869] NVM is EFUSE
[ 3539.912870] Endpoint(8) is for In-band Command
[ 3539.912871] Endpoint(4) is for WMM0 AC0
[ 3539.912871] Endpoint(5) is for WMM0 AC1
[ 3539.912872] Endpoint(6) is for WMM0 AC2
[ 3539.912872] Endpoint(7) is for WMM0 AC3
[ 3539.912873] Endpoint(9) is for WMM1 AC0
[ 3539.912874] Endpoint(84) is for Data-In
[ 3539.912874] Endpoint(85) is for Command Rsp
[ 3632.642059] -->RTUSBVenderReset
[ 3632.642162] <--RTUSBVenderReset
[ 3632.647128] fw version:0.1.00 build:7640
[ 3632.647130] build time:201308221655____
[ 3632.647135] ilm length = 68780(bytes)
[ 3632.647136] dlm length = 11476(bytes)
[ 3632.729684] #
[ 3632.736655] loading fw......
[ 3632.857890] #
[ 3633.074167] RTMP_TimerListAdd: add timer obj ffffc64740ba61e0!
[ 3633.074169] RTMP_TimerListAdd: add timer obj ffffc64740ba6250!
[ 3633.074170] RTMP_TimerListAdd: add timer obj ffffc64740ba62c0!
[ 3633.074171] RTMP_TimerListAdd: add timer obj ffffc64740ba6170!
[ 3633.086233] cfg_mode=5
[ 3633.086236] wmode_band_equal(): Band Not Equal!
[ 3633.086350] Key1Str is Invalid key length(0) or Type(0)
[ 3633.086361] Key2Str is Invalid key length(0) or Type(0)
[ 3633.086372] Key3Str is Invalid key length(0) or Type(0)
[ 3633.086383] Key4Str is Invalid key length(0) or Type(0)
[ 3633.086687] 1. Phy Mode = 31
[ 3633.086688] 2. Phy Mode = 31
[ 3633.086690] NVM is Efuse and its size =1d[1e0-1fc]
[ 3633.097715] /root/src/mt7610u_wifi_sta_v3002_dpo_20130916/os/linux/../../chips/mt76x0.c:2114 assert (pAd->TxPower[choffset].Channel == 36)failed
[ 3633.111176] ERROR!!! E2PROM: WRONG VERSION 0x2, should be 1
[ 3633.115302] mt76x0_read_tx_alc_info_from_eeprom: EEPROM_MT76x0_TEMPERATURE_OFFSET (0xD1) = 0xf8
[ 3633.115303] mt76x0_read_tx_alc_info_from_eeprom: TemperatureOffset = 0xfffffff8
[ 3633.115303] Temperature Tx ALC not enabled
[ 3633.130303] 3. Phy Mode = 31
[ 3633.130305] AntCfgInit: primary/secondary ant 0/1
[ 3633.138969] RTMPSetPhyMode: channel is out of range, use first channel=1
[ 3633.140555] MCS Set = ff 00 00 00 01
[ 3633.150491] <==== rt28xx_init, Status=0
[ 3633.151431] 0x1300 = 00064300
[ 3633.151432] RTMPDrvSTAOpen(1):Check if PDMA is idle!
[ 3633.151556] RTMPDrvSTAOpen(2):Check if PDMA is idle!
[ 4260.799872] receive cmd msg fail(-71)
[ 4260.799965] Bulk In Failed. Status=-71, BIIdx=0x0, BIRIdx=0x0, actual_length= 0x0
[ 4260.804373] receive cmd msg fail(-71)
[ 4260.808616] receive cmd msg fail(-71)
[ 4260.812867] receive cmd msg fail(-71)
[ 4260.817116] receive cmd msg fail(-71)
[ 4260.898248] receive cmd msg fail(-71)
[ 4260.900248] RTUSB_VendorRequest failed(-71),TxFlags=0x0, ReqType=IN, Req=0x7, Idx=0x1000,pAd->Flags=0x31080002
[ 4260.902500] receive cmd msg fail(-71)
[ 4260.904250] Bulk In Failed. Status=-71, BIIdx=0x0, BIRIdx=0x0, actual_length= 0x0
[ 4260.945005] receive cmd msg fail(-71)
[ 4261.000507] receive cmd msg fail(-71)
[ 4261.003855] RTUSB_VendorRequest failed(-71),TxFlags=0x0, ReqType=IN, Req=0x7, Idx=0x1000,pAd->Flags=0x31080002
[ 4261.004758] receive cmd msg fail(-71)
[ 4261.007759] Bulk In Failed. Status=-71, BIIdx=0x0, BIRIdx=0x0, actual_length= 0x0
[ 4261.009009] receive cmd msg fail(-71)
[ 4261.034139] usb 1-1.3: USB disconnect, device number 8
[ 4261.034509] receive cmd msg fail(-108)
[ 4261.034511] usb_rx_cmd_msg_complete:submit urb fail(-19)
[ 4261.034517] usb_rx_cmd_msg_submit:submit urb fail(-19)
[ 4261.034519] rtusb_disconnect: unregister usbnet usb-0000:00:1d.0-1.3
[ 4261.034522] RtmpOSNetDevDetach(): RtmpOSNetDeviceDetach(), dev->name=ra0!
[ 4261.035606] #
[ 4261.035608] RTUSB_VendorRequest failed(-19),TxFlags=0x0, ReqType=IN, Req=0x7, Idx=0x1000,pAd->Flags=0x31080542
[ 4261.035609] CMDTHREAD_RESET_BULK_IN: Cannot do bulk in because flags(0x31080542) on !
[ 4261.049617] WIFI device has been disconnected
[ 4261.049668] WIFI device has been disconnected
[ 4261.049668] WIFI device has been disconnected
[ 4261.049669] WIFI device has been disconnected
[ 4261.049673] tx_kickout_fail_count = 0
[ 4261.049673] tx_timeout_fail_count = 0
[ 4261.049674] rx_receive_fail_count = 58
[ 4261.049674] alloc_cmd_msg = 7672
[ 4261.049675] free_cmd_msg = 7672
[ 4261.132674] WIFI device has been disconnected
[ 4261.132677] ==>RT65xx_WLAN_ChipOnOff(): OnOff:0, Reset= 0, pAd->WlanFunCtrl:0xff000003, Reg-WlanFunCtrl=0xffffffff
[ 4261.132677] WIFI device has been disconnected
[ 4261.132678] VendrCmdMultiWrite_nBytes failed!
[ 4261.132698] WIFI device has been disconnected
[ 4261.132708] ---> RTMPFreeTxRxRingMemory
[ 4261.132722] <--- RTMPFreeTxRxRingMemory
[ 4261.132759] RTUSB disconnect successfully
[ 4981.190839] usb 1-1.3: new high-speed USB device number 9 using ehci-pci
[ 4981.315282] usb 1-1.3: New USB device found, idVendor=148f, idProduct=761a
[ 4981.315284] usb 1-1.3: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 4981.315285] usb 1-1.3: Product: WiFi
[ 4981.315286] usb 1-1.3: Manufacturer: MediaTek
[ 4981.315287] usb 1-1.3: SerialNumber: 1.0
[ 4981.315819]
=== pAd = ffffc64740b25000, size = 892576 ===
[ 4981.315904] <-- RTMPAllocTxRxRingMemory, Status=0
[ 4981.316006] <-- RTMPAllocAdapterBlock, Status=0
[ 4981.316133] ==>RT65xx_WLAN_ChipOnOff(): OnOff:1, Reset= 0, pAd->WlanFunCtrl:0x0, Reg-WlanFunCtrl=0xff000002
[ 4981.317259] MCUType = 2
[ 4981.317507] NVM is EFUSE
[ 4981.317508] Endpoint(8) is for In-band Command
[ 4981.317509] Endpoint(4) is for WMM0 AC0
[ 4981.317509] Endpoint(5) is for WMM0 AC1
[ 4981.317510] Endpoint(6) is for WMM0 AC2
[ 4981.317511] Endpoint(7) is for WMM0 AC3
[ 4981.317511] Endpoint(9) is for WMM1 AC0
[ 4981.317512] Endpoint(84) is for Data-In
[ 4981.317512] Endpoint(85) is for Command Rsp
[ 5382.065830] -->RTUSBVenderReset
[ 5382.066025] <--RTUSBVenderReset
[ 5382.070992] fw version:0.1.00 build:7640
[ 5382.070994] build time:201308221655____
[ 5382.071000] ilm length = 68780(bytes)
[ 5382.071000] dlm length = 11476(bytes)
[ 5382.152631] #
[ 5382.158632] loading fw......
[ 5382.276688] #
[ 5382.494398] RTMP_TimerListAdd: add timer obj ffffc64740ba61e0!
[ 5382.494400] RTMP_TimerListAdd: add timer obj ffffc64740ba6250!
[ 5382.494401] RTMP_TimerListAdd: add timer obj ffffc64740ba62c0!
[ 5382.494402] RTMP_TimerListAdd: add timer obj ffffc64740ba6170!
[ 5382.494408] RTMP_TimerListAdd: add timer obj ffffc64740b38c38!
[ 5382.494409] RTMP_TimerListAdd: add timer obj ffffc64740b38e18!
[ 5382.494466] cfg_mode=5
[ 5382.494468] wmode_band_equal(): Band Not Equal!
[ 5382.494582] Key1Str is Invalid key length(0) or Type(0)
[ 5382.494593] Key2Str is Invalid key length(0) or Type(0)
[ 5382.494604] Key3Str is Invalid key length(0) or Type(0)
[ 5382.494616] Key4Str is Invalid key length(0) or Type(0)
[ 5382.494856] 1. Phy Mode = 31
[ 5382.494856] 2. Phy Mode = 31
[ 5382.494858] NVM is Efuse and its size =1d[1e0-1fc]
[ 5382.506903] /root/src/mt7610u_wifi_sta_v3002_dpo_20130916/os/linux/../../chips/mt76x0.c:2114 assert (pAd->TxPower[choffset].Channel == 36)failed
[ 5382.517405] ERROR!!! E2PROM: WRONG VERSION 0x2, should be 1
[ 5382.521530] mt76x0_read_tx_alc_info_from_eeprom: EEPROM_MT76x0_TEMPERATURE_OFFSET (0xD1) = 0xf8
[ 5382.521531] mt76x0_read_tx_alc_info_from_eeprom: TemperatureOffset = 0xfffffff8
[ 5382.521532] Temperature Tx ALC not enabled
[ 5382.537531] 3. Phy Mode = 31
[ 5382.537533] AntCfgInit: primary/secondary ant 0/1
[ 5382.542790] RTMPSetPhyMode: channel is out of range, use first channel=1
[ 5382.544283] MCS Set = ff 00 00 00 01
[ 5382.554214] <==== rt28xx_init, Status=0
[ 5382.555157] 0x1300 = 00064300
[ 5382.555158] RTMPDrvSTAOpen(1):Check if PDMA is idle!
[ 5382.555314] RTMPDrvSTAOpen(2):Check if PDMA is idle!
[ 5482.218330] ===>rt_ioctl_giwscan. 2(2) BSS returned, data->length = 317
[ 5550.260554] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 5550.293209] ERROR!!! RTMPSetTimer failed, Halt in Progress!
[ 5550.300208] ==>RT65xx_WLAN_ChipOnOff(): OnOff:0, Reset= 0, pAd->WlanFunCtrl:0xff000003, Reg-WlanFunCtrl=0xff000003
[ 5550.303830] receive cmd msg fail(-2)
[ 5550.303842] tx_kickout_fail_count = 0
[ 5550.303844] tx_timeout_fail_count = 0
[ 5550.303845] rx_receive_fail_count = 0
[ 5550.303846] alloc_cmd_msg = 6981
[ 5550.303846] free_cmd_msg = 6981
[ 5550.359595] ==>RT65xx_WLAN_ChipOnOff(): OnOff:1, Reset= 0, pAd->WlanFunCtrl:0xff000000, Reg-WlanFunCtrl=0xff000000
[ 5550.366721] -->RTUSBVenderReset
[ 5550.366846] <--RTUSBVenderReset
[ 5550.371809] fw version:0.1.00 build:7640
[ 5550.371811] build time:201308221655____
[ 5550.371825] ilm length = 68780(bytes)
[ 5550.371825] dlm length = 11476(bytes)
[ 5550.451175] #
[ 5550.457901] loading fw......
[ 5550.796383] RTMP_TimerListAdd: add timer obj ffffc64740b38d18!
[ 5550.796384] RTMP_TimerListAdd: add timer obj ffffc64740b27b80!
[ 5550.796384] RTMP_TimerListAdd: add timer obj ffffc64740b27bf8!
[ 5550.796385] RTMP_TimerListAdd: add timer obj ffffc64740b38e88!
[ 5550.796386] RTMP_TimerListAdd: add timer obj ffffc64740b38c38!
[ 5550.796387] RTMP_TimerListAdd: add timer obj ffffc64740b38e18!
[ 5550.796444] cfg_mode=5
[ 5550.796446] wmode_band_equal(): Band Not Equal!
[ 5550.796559] Key1Str is Invalid key length(0) or Type(0)
[ 5550.796570] Key2Str is Invalid key length(0) or Type(0)
[ 5550.796581] Key3Str is Invalid key length(0) or Type(0)
[ 5550.796592] Key4Str is Invalid key length(0) or Type(0)
[ 5550.796832] 1. Phy Mode = 31
[ 5550.796833] 2. Phy Mode = 31
[ 5550.796834] NVM is Efuse and its size =1d[1e0-1fc]
[ 5550.807751] /root/src/mt7610u_wifi_sta_v3002_dpo_20130916/os/linux/../../chips/mt76x0.c:2114 assert (pAd->TxPower[choffset].Channel == 36)failed
[ 5550.818252] ERROR!!! E2PROM: WRONG VERSION 0x2, should be 1
[ 5550.822377] mt76x0_read_tx_alc_info_from_eeprom: EEPROM_MT76x0_TEMPERATURE_OFFSET (0xD1) = 0xf8
[ 5550.822378] mt76x0_read_tx_alc_info_from_eeprom: TemperatureOffset = 0xfffffff8
[ 5550.822378] Temperature Tx ALC not enabled
[ 5550.839378] 3. Phy Mode = 31
[ 5550.839379] AntCfgInit: primary/secondary ant 0/1
[ 5550.844637] RTMPSetPhyMode: channel is out of range, use first channel=1
[ 5550.846035] MCS Set = ff 00 00 00 01
[ 5550.855972] <==== rt28xx_init, Status=0
[ 5550.857128] 0x1300 = 00064300
[ 5550.857129] RTMPDrvSTAOpen(1):Check if PDMA is idle!
[ 5550.857255] RTMPDrvSTAOpen(2):Check if PDMA is idle!
[ 5551.014244] BUG: unable to handle kernel paging request at 00007fff13453d00
[ 5551.014316] IP: [<ffffffffc0df441a>] rt_ioctl_siwpmksa+0x8a/0x140 [mt7650u_sta]
[ 5551.014402] PGD 116cca067 PUD 11599c067 PMD 117fd0067 PTE 800000010a6d3867
[ 5551.014467] Oops: 0001 [#1] SMP
[ 5551.014494] Modules linked in: fuse nfnetlink_queue nfnetlink_log nfnetlink binfmt_misc wl(PO) mt7650u_sta(O) snd_hda_codec_hdmi intel_rapl x86_pkg_temp_thermal intel_powerclamp coretemp btusb btrtl btbcm btintel uvcvideo bluetooth videobuf2_vmalloc kvm_intel dcdbas videobuf2_memops iTCO_wdt snd_hda_codec_realtek videobuf2_v4l2 iTCO_vendor_support kvm hid_rmi dell_smm_hwmon videobuf2_core videodev irqbypass snd_hda_codec_generic cfg80211 snd_hda_intel rtsx_usb_ms hid_multitouch memstick pcspkr media snd_soc_rt5640 snd_hda_codec snd_soc_ssm4567 snd_soc_rl6231 snd_soc_core snd_hda_core joydev evdev snd_hwdep snd_compress snd_pcm sg serio_raw i915 wmi snd_timer snd shpchp dw_dmac battery video elan_i2c dell_rbtn rfkill i2c_i801 dw_dmac_core snd_soc_sst_acpi mei_me mei snd_soc_sst_match lpc_ich drm_kms_helper
[ 5551.015186] soundcore i2c_smbus acpi_pad ac button drm i2c_algo_bit tpm_tis tpm_tis_core tpm i2c_designware_platform i2c_designware_core ip_tables x_tables autofs4 rtsx_usb_sdmmc rtsx_usb mfd_core ext4 crc16 usbhid jbd2 crc32c_generic fscrypto ecb mbcache sr_mod cdrom sd_mod crct10dif_pclmul crc32_pclmul crc32c_intel ghash_clmulni_intel aesni_intel aes_x86_64 lrw gf128mul glue_helper ablk_helper cryptd ahci libahci psmouse xhci_pci xhci_hcd libata ehci_pci ehci_hcd scsi_mod r8169 mii usbcore usb_common fan thermal sdhci_acpi sdhci mmc_core fjes i2c_hid hid
[ 5551.015700] CPU: 0 PID: 838 Comm: wpa_supplicant Tainted: P O 4.8.0-kali1-amd64 #1 Debian 4.8.5-1kali1
[ 5551.015775] Hardware name: Dell Inc. Inspiron 3543/0MGXC6, BIOS A00 10/25/2014
[ 5551.015832] task: ffff906d98270080 task.stack: ffff906d934a4000
[ 5551.015874] RIP: 0010:[<ffffffffc0df441a>] [<ffffffffc0df441a>] rt_ioctl_siwpmksa+0x8a/0x140 [mt7650u_sta]
[ 5551.015974] RSP: 0018:ffff906d934a7ca8 EFLAGS: 00010297
[ 5551.016016] RAX: 0000000000000000 RBX: 00007fff13453d00 RCX: 0000000000000000
[ 5551.016067] RDX: 0000000000005013 RSI: 0000000000000000 RDI: ffffc64740b25000
[ 5551.016119] RBP: 0000000000000000 R08: 0000000000000000 R09: 0000000000000000
[ 5551.016169] R10: 0000000000000036 R11: ffffffffc0df4390 R12: ffffc64740b25000
[ 5551.016224] R13: ffff906d0ca3d000 R14: ffffffff8429a888 R15: ffffffffc0df4390
[ 5551.016275] FS: 00007f275db5a880(0000) GS:ffff906d9ec00000(0000) knlGS:0000000000000000
[ 5551.016338] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 5551.016382] CR2: 00007fff13453d00 CR3: 0000000116c12000 CR4: 00000000003406f0
[ 5551.016437] Stack:
[ 5551.016456] ffff906cacae6a00 ffff906d941d1000 ffff906d93dbd900 0000000000000024
[ 5551.016522] 000000005485238f ffff906d2a0b0540 ffff906d934a7e20 0000000000000000
[ 5551.016586] 0000000000008b36 ffffffff841ce8b8 ffff906d0ca3d000 00007fff13453d00
[ 5551.016652] Call Trace:
[ 5551.016681] [<ffffffff841ce8b8>] ? ioctl_standard_iw_point+0x2e8/0x3c0
[ 5551.016734] [<ffffffff841cea3a>] ? ioctl_standard_call+0xaa/0xd0
[ 5551.016783] [<ffffffff841cec55>] ? wext_handle_ioctl+0x75/0xd0
[ 5551.016828] [<ffffffff840fa62f>] ? dev_ioctl+0x29f/0x580
[ 5551.016871] [<ffffffff840bf8bd>] ? sock_ioctl+0x11d/0x280
[ 5551.016916] [<ffffffff83e1334f>] ? do_vfs_ioctl+0x9f/0x5f0
[ 5551.016962] [<ffffffff83dff6d0>] ? vfs_read+0x90/0x130
[ 5551.017006] [<ffffffff83e13914>] ? SyS_ioctl+0x74/0x80
[ 5551.017047] [<ffffffff841e18f6>] ? system_call_fast_compare_end+0xc/0x96
[ 5551.017100] Code: 00 bd 9c ff ff ff eb 78 48 85 db 0f 84 a0 00 00 00 48 83 3d 40 23 04 00 02 89 c5 76 0e 48 83 3d 5c a5 06 00 00 0f 84 a5 00 00 00 <8b> 03 83 f8 03 74 6b 83 f8 02 74 70 83 f8 01 0f 94 c0 0f b6 c0
[ 5551.017394] RIP [<ffffffffc0df441a>] rt_ioctl_siwpmksa+0x8a/0x140 [mt7650u_sta]
[ 5551.017477] RSP <ffff906d934a7ca8>
[ 5551.017504] CR2: 00007fff13453d00
[ 5551.027427] ---[ end trace 59de0c89298499a0 ]---
答案1
我必须在我的旧笔记本电脑（带 RT5390 的 HP g6）上执行此操作。
许多字段保持空白，包括我曾经填充过的 ssid，但它不是必需的。
要做的主要事情是有几个文件需要编辑预构建。
我启动我的旧笔记本电脑来检查...重新提取焦油并进行合并...
配置文件
HAS_NATIVE_WPA_SUPPLICANT_SUPPORT=n
changed to:
HAS_NATIVE_WPA_SUPPLICANT_SUPPORT=y
pci_main_dev.c
注释掉了一些阻止的逻辑：
SET_NETDEV_DEV(net_dev,&(pci-dev->dev))
（没有那个网络管理器将不受支持，但逻辑是针对内核2.6.0的，不记得我是否真的在那场比赛上有那么旧的内核......可能在某个时候做过）。
rt_linux.c
我编辑了 skb->tail 将其转换为 unsigned int 32 位。
最后在 makefile 中：
- 我删除了周围的逻辑并更改了;芯片组 = 5390
- 删除了所有PC平台
- 删除了 MAKE MAKE = make 周围的所有逻辑
（你可能不必执行所有这些步骤，因为我想象现在他们有一个更好的版本，但他们就在那里......）
关于dat文件，我改变了3x值； （但如果您为网络管理器进行编译，则不需要它们，就像我稍后所做的那样）。
- SSID=
- EncrypType=wpa-psk
- WPAPSK=
完成所有构建后，我将 dat 文件放入；
/etc/Wireless/RT5390STA/RT5390STA.dat
/etc/Wireless/RT5390STA/RT5390STACard.dat
如果您愿意或者有帮助，为了进行比较，我可以复制 .dat 文件。
更新：查找模块到黑名单；使用;
sudo lscpi -v | less
我当前机器的输出示例；
03:00.0 Network controller: Intel Corporation Wireless 3165 (rev 81)
DeviceName: SP1
Subsystem: Intel Corporation Dual Band Wireless AC 3165
Flags: bus master, fast devsel, latency 0, IRQ 42
Memory at f1000000 (64-bit, non-prefetchable) [size=8K]
Capabilities: [c8] Power Management version 3
Capabilities: [d0] MSI: Enable+ Count=1/1 Maskable- 64bit+
Capabilities: [40] Express Endpoint, MSI 00
Capabilities: [100] Advanced Error Reporting
Capabilities: [140] Device Serial Number dc-53-60-ff-ff-5f-cb-f2
Capabilities: [14c] Latency Tolerance Reporting
Capabilities: [154] L1 PM Substates
Kernel driver in use: iwlwifi
Kernel modules: iwlwifi
在这种情况下，我会在 /etc/modprobe.d/wifi.conf 中列入黑名单
blacklist iwlwifi
重复此操作，直到您在无线设备上看到：
Kernel driver in use: rt2800pci
更新：
我挖出了我的 tp-link USB 适配器（OP 正在尝试对 USB 而不是 pci 设备进行排序）。
我还没有编译 USB 的源代码，这只是与我的内核和固件 blob 一起工作已经可用。
[ 25.502040] usb 2-1: new high-speed USB device number 2 using xhci_hcd
[ 25.660113] usb 2-1: New USB device found, idVendor=148f, idProduct=5572
[ 25.660124] usb 2-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 25.660129] usb 2-1: Product: 802.11 n WLAN
[ 25.660133] usb 2-1: Manufacturer: Ralink
[ 25.660136] usb 2-1: SerialNumber: 1.0
[ 25.827234] usb 2-1: reset high-speed USB device number 2 using xhci_hcd
[ 25.977689] ieee80211 phy1: rt2x00_set_rt: Info - RT chipset 5592, rev 0222 detected
[ 26.088458] ieee80211 phy1: rt2x00_set_rf: Info - RF chipset 000f detected
[ 26.090545] ieee80211 phy1: Selected rate control algorithm 'minstrel_ht'
[ 26.092720] usbcore: registered new interface driver rt2800usb
[ 26.122102] ieee80211 phy1: rt2x00lib_request_firmware: Info - Loading firmware file 'rt2870.bin'
[ 26.122379] ieee80211 phy1: rt2x00lib_request_firmware: Info - Firmware detected - version: 0.29
以下是当前的内核模块：
$ lsmod | grep rt2
rt2800usb 28672 0
rt2x00usb 20480 1 rt2800usb
rt2800lib 81920 1 rt2800usb
rt2x00lib 45056 3 rt2800lib,rt2800usb,rt2x00usb
crc_ccitt 16384 1 rt2800lib
mac80211 569344 4 rt2800lib,iwlmvm,rt2x00lib,rt2x00usb
cfg80211 471040 4 iwlmvm,iwlwifi,rt2x00lib,mac80211
usbcore 208896 6 rt2800usb,rt2x00usb,ehci_hcd,xhci_pci,xhci_hcd,ehci_pci
固件 blob 来自此包：
firmware-misc-nonfree: /lib/firmware/rt2870.bin
如果OP愿意，我可以用这个USB设备测试源码包吗？
答案2
查看这个包：https://aur.archlinux.org/packages/mt7610u_wifi_sta/
我相信你会找到宝贵的信息