电脑不会进入睡眠状态，因为我禁用了该功能，并且在合上盖子的情况下工作，但一段时间后，系统断开网络并物理访问设备导致屏幕关闭（不是在没有显示的情况下打开，而是关闭） ）键盘灯仍然有效，按下大写字母可打开或关闭灯，但显示器无法打开，也无法连接到网络
我已将loginctl配置为忽略lidswitch，该开关在PC从wifi网络断开之前工作了几个小时，并且在物理访问时拒绝打开，并且在断开PC连接时PC重新连接到wifi，几分钟内断开了wifi连接。
我查看了 dmesg 并搜索了有关我的 wifi 驱动程序的内容ath10k，但没有显示任何异常情况
[ 10.421971] ath10k_pci 0000:02:00.0: pci irq msi oper_irq_mode 2 irq_mode 0 reset_mode 0
[ 10.702774] ath10k_pci 0000:02:00.0: firmware: failed to load ath10k/pre-cal-pci-0000:02:00.0.bin (-2)
[ 10.702813] ath10k_pci 0000:02:00.0: firmware: failed to load ath10k/pre-cal-pci-0000:02:00.0.bin (-2)
[ 10.702850] ath10k_pci 0000:02:00.0: firmware: failed to load ath10k/cal-pci-0000:02:00.0.bin (-2)
[ 10.702872] ath10k_pci 0000:02:00.0: firmware: failed to load ath10k/cal-pci-0000:02:00.0.bin (-2)
[ 10.706800] ath10k_pci 0000:02:00.0: firmware: direct-loading firmware ath10k/QCA9377/hw1.0/firmware-6.bin
[ 10.706824] ath10k_pci 0000:02:00.0: qca9377 hw1.0 target 0x05020000 chip_id 0x003820ff sub 17aa:4035
[ 10.706830] ath10k_pci 0000:02:00.0: kconfig debug 0 debugfs 0 tracing 0 dfs 0 testmode 0
[ 10.707653] ath10k_pci 0000:02:00.0: firmware ver WLAN.TF.2.1-00021-QCARMSWP-1 api 6 features wowlan,ignore-otp crc32 42e41877
[ 10.782139] ath10k_pci 0000:02:00.0: firmware: direct-loading firmware ath10k/QCA9377/hw1.0/board-2.bin
[ 10.782437] ath10k_pci 0000:02:00.0: board_file api 2 bmi_id N/A crc32 8aedfa4a
[ 13.101787] ath10k_pci 0000:02:00.0: htt-ver 3.56 wmi-op 4 htt-op 3 cal otp max-sta 32 raw 0 hwcrypto 1
[ 14.340785] ath10k_pci 0000:02:00.0 wlp2s0: renamed from wlan0
加载失败的线路是无害 这是无线网卡
02:00.0 Network controller: Qualcomm Atheros QCA9377 802.11ac Wireless Network Adapter (rev 30)
Subsystem: Lenovo QCA9377 802.11ac Wireless Network Adapter
Kernel driver in use: ath10k_pci
Kernel modules: ath10k_pci
03:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL810xE PCI Express Fast Ethernet controller (rev 07)
Subsystem: Lenovo RTL810xE PCI Express Fast Ethernet controller
Kernel driver in use: r8169
Kernel modules: r8169
我使用 systemd-networkd 来管理我的连接，因为 OpenMediaVault 附带它，我使用的是最新的 debian 12 bookwork 稳定版本。
输出inxi -Fzaa
System:
Kernel: 6.1.0-16-amd64 arch: x86_64 bits: 64 compiler: gcc v: 12.2.0
parameters: BOOT_IMAGE=/boot/vmlinuz-6.1.0-16-amd64
root=UUID=8e612ff6-1299-49b8-963e-fac36e627625 ro quiet
rd.luks.uuid=3f9c700c-27cb-4d44-af3c-0d6ba0d21e0f loglevel=3 radeon.cik_support=0
amdgpu.cik_support=1 radeon.si_support=0 amdgpu.si_support=1
Console: pty pts/0 Distro: openmediavault 7.0-19 (Sandworm) base: Debian GNU/Linux 12
(bookworm)
Machine:
Type: Laptop System: LENOVO product: 80TJ v: Lenovo ideapad 110-15ACL
serial: <superuser required> Chassis: type: 10 v: Lenovo ideapad 110-15ACL
serial: <superuser required>
Mobo: LENOVO model: Nano 5A8 v: SDK0J40679 WIN serial: <superuser required> UEFI: Lenovo
v: 1QCN32WW date: 08/18/2016
Battery:
ID-1: BATT charge: 0 Wh (0.0%) condition: 1.6/23.8 Wh (6.7%) volts: 7.2 min: 10.8
model: LENOVO LCFC type: Unknown serial: <filter> status: not charging
CPU:
Info: model: AMD A8-7410 APU with AMD Radeon R5 Graphics bits: 64 type: MCP arch: Puma level: v2
built: 2014-15 process: GF 28nm family: 0x16 (22) model-id: 0x30 (48) stepping: 1
microcode: 0x7030105
Topology: cpus: 1x cores: 4 smt: <unsupported> cache: L1: 256 KiB desc: d-4x32 KiB; i-4x32 KiB
L2: 2 MiB desc: 1x2 MiB
Speed (MHz): avg: 998 min/max: 1000/2200 boost: enabled scaling: driver: acpi-cpufreq
governor: conservative cores: 1: 998 2: 998 3: 998 4: 998 bogomips: 17567
Flags: avx ht lm nx pae sse sse2 sse3 sse4_1 sse4_2 sse4a ssse3 svm
Vulnerabilities:
Type: gather_data_sampling status: Not affected
Type: itlb_multihit status: Not affected
Type: l1tf status: Not affected
Type: mds status: Not affected
Type: meltdown status: Not affected
Type: mmio_stale_data status: Not affected
Type: retbleed mitigation: untrained return thunk; SMT disabled
Type: spec_rstack_overflow status: Not affected
Type: spec_store_bypass mitigation: Speculative Store Bypass disabled via prctl
Type: spectre_v1 mitigation: usercopy/swapgs barriers and __user pointer sanitization
Type: spectre_v2 mitigation: Retpolines, STIBP: disabled, RSB filling, PBRSB-eIBRS: Not
affected
Type: srbds status: Not affected
Type: tsx_async_abort status: Not affected
Graphics:
Device-1: AMD Mullins [Radeon R4/R5 Graphics] vendor: Lenovo driver: amdgpu v: kernel
alternate: radeon arch: GCN-2 code: Sea Islands process: GF/TSMC 16-28nm built: 2013-17 ports:
active: eDP-1 empty: HDMI-A-1 bus-ID: 00:01.0 chip-ID: 1002:9851 class-ID: 0300
Device-2: AMD Sun XT [Radeon HD 8670A/8670M/8690M / R5 M330 M430 Radeon 520 Mobile]
vendor: Lenovo driver: amdgpu v: kernel alternate: radeon arch: GCN-1 code: Southern Islands
process: TSMC 28nm built: 2011-20 pcie: gen: 2 speed: 5 GT/s lanes: 2 link-max: gen: 3
speed: 8 GT/s lanes: 8 bus-ID: 01:00.0 chip-ID: 1002:6660 class-ID: 0380 temp: 41.0 C
Device-3: IMC Networks EasyCamera type: USB driver: uvcvideo bus-ID: 2-1.2:4
chip-ID: 13d3:a745 class-ID: 0e02 serial: <filter>
Display: server: No display server data found. Headless machine? tty: 110x28
Monitor-1: eDP-1 model: ChiMei InnoLux 0x15dc built: 2015 res: 1366x768 dpi: 101 gamma: 1.2
size: 344x193mm (13.54x7.6") diag: 394mm (15.5") ratio: 16:9 modes: max: 1366x768 min: 640x480
API: N/A Message: No display API data available in console. Headless machine?
Audio:
Device-1: AMD Kabini HDMI/DP Audio vendor: Lenovo driver: snd_hda_intel v: kernel
bus-ID: 00:01.1 chip-ID: 1002:9840 class-ID: 0403
Device-2: AMD FCH Azalia vendor: Lenovo driver: snd_hda_intel v: kernel bus-ID: 00:14.2
chip-ID: 1022:780d class-ID: 0403
API: ALSA v: k6.1.0-16-amd64 status: kernel-api tools: N/A
Network:
Device-1: Qualcomm Atheros QCA9377 802.11ac Wireless Network Adapter vendor: Lenovo
driver: ath10k_pci v: kernel pcie: gen: 1 speed: 2.5 GT/s lanes: 1 bus-ID: 02:00.0
chip-ID: 168c:0042 class-ID: 0280
IF: wlp2s0 state: up mac: <filter>
Device-2: Realtek RTL810xE PCI Express Fast Ethernet vendor: Lenovo driver: r8169 v: kernel
pcie: gen: 1 speed: 2.5 GT/s lanes: 1 port: 1000 bus-ID: 03:00.0 chip-ID: 10ec:8136
class-ID: 0200
IF: enp3s0 state: up speed: 100 Mbps duplex: full mac: <filter>
IF-ID-1: br-2843d63134e5 state: up speed: 10000 Mbps duplex: unknown mac: <filter>
IF-ID-2: docker0 state: up speed: 10000 Mbps duplex: unknown mac: <filter>
IF-ID-3: tailscale0 state: unknown speed: -1 duplex: full mac: N/A
IF-ID-4: veth0b5fec8 state: up speed: 10000 Mbps duplex: full mac: <filter>
IF-ID-5: veth11e2b4f state: up speed: 10000 Mbps duplex: full mac: <filter>
IF-ID-6: veth31582f8 state: up speed: 10000 Mbps duplex: full mac: <filter>
Bluetooth:
Device-1: Qualcomm Atheros type: USB driver: btusb v: 0.8 bus-ID: 2-1.1:3 chip-ID: 0cf3:e360
class-ID: e001
Report: rfkill ID: hci0 rfk-id: 2 state: down bt-service: not found rfk-block: hardware: no
software: yes address: see --recommends
Drives:
Local Storage: total: 2.04 TiB used: 781.11 GiB (37.4%)
SMART Message: Unable to run smartctl. Root privileges required.
ID-1: /dev/sda maj-min: 8:0 vendor: Western Digital model: WDS240G2G0A-00JH30 size: 223.58 GiB
block-size: physical: 512 B logical: 512 B speed: 6.0 Gb/s type: SSD serial: <filter> rev: 0000
temp: 41 C scheme: GPT
ID-2: /dev/sdb maj-min: 8:16 type: USB vendor: Seagate model: BUP Slim RD size: 931.51 GiB
block-size: physical: 4096 B logical: 512 B type: N/A serial: <filter> rev: 0302
ID-3: /dev/sdc maj-min: 8:32 type: USB vendor: Seagate model: BUP Slim WH size: 931.51 GiB
block-size: physical: 4096 B logical: 512 B type: N/A serial: <filter> rev: 0304
Partition:
ID-1: / raw-size: 37.93 GiB size: 37.04 GiB (97.65%) used: 30.31 GiB (81.8%) fs: ext4
dev: /dev/sda5 maj-min: 8:5
ID-2: /boot/efi raw-size: 500 MiB size: 499 MiB (99.80%) used: 16.6 MiB (3.3%) fs: vfat
dev: /dev/sda1 maj-min: 8:1
Swap:
Kernel: swappiness: 1 (default 60) cache-pressure: 50 (default 100)
ID-1: swap-1 type: file size: 4 GiB used: 0 KiB (0.0%) priority: -2 file: /swapfile
Sensors:
System Temperatures: cpu: 49.5 C mobo: N/A
Fan Speeds (RPM): N/A
GPU: device: amdgpu temp: 41.0 C device: amdgpu temp: 46.0 C
Info:
Processes: 243 Uptime: 16h 47m wakeups: 2 Memory: 6.68 GiB used: 2.04 GiB (30.6%) Init: systemd
v: 252 target: graphical (5) default: graphical tool: systemctl Compilers: gcc: 12.2.0
alt: 10/12 Packages: 1220 pm: dpkg pkgs: 1216 libs: 693 tools: apt,apt-get pm: snap pkgs: 4
Shell: Bash v: 5.2.15 running-in: pty pts/0 (SSH) inxi: 3.3.26
这是logind.conf
[Login]
#NAutoVTs=6
#ReserveVT=6
#KillUserProcesses=no
#KillOnlyUsers=
#KillExcludeUsers=root
#InhibitDelayMaxSec=5
#UserStopDelaySec=10
HandlePowerKey = ignore
#HandleSuspendKey=suspend
#HandleHibernateKey=hibernate
HandleLidSwitch = ignore
#HandleLidSwitchExternalPower=suspend
#HandleLidSwitchDocked=ignore
#HandleRebootKey=reboot
#PowerKeyIgnoreInhibited=no
#SuspendKeyIgnoreInhibited=no
#HibernateKeyIgnoreInhibited=no
LidSwitchIgnoreInhibited = no
#RebootKeyIgnoreInhibited=no
#HoldoffTimeoutSec=30s
#IdleAction=ignore
#IdleActionSec=30min
#RuntimeDirectorySize=10%
#RuntimeDirectoryInodes=400k
#RemoveIPC=yes
#InhibitorsMax=8192
#SessionsMax=8192
登录部分（盖子关闭时不会暂停）可以完美地工作几个小时，所以我怀疑其中存在问题。