添加阀杆、夹具和螺母

Question

我开始使用 pst-labo 软件包制作化学图表。我理解了原理，很容易理解，可以追踪它们。我想通过添加杆、螺母和夹子来装饰组件：我该怎么做？

谢谢您的帮助

\documentclass{article}
\usepackage{pst-labo}

\begin{document}

\psset{ unit =0.5cm}
\psgrid[subgriddiv=1,griddots=10,  gridlabels=5pt, gridwidth=0.5pt](0,0)(20,20)
\pstBallon[ refrigerantBoulles ,glassType=ballon]

\end{document}

最终的图表大致对应如下：

Answer 1

您可以像本例一样绘制自己的。然后可以使用命令\rput将其移动到所需位置。

\documentclass{article}
\usepackage{pst-labo}

\newcommand{\pstClamp}{
    \colorlet{myfill}{brown!60}
    % potence
    \psframe[fillstyle=solid, fillcolor=myfill](-.5,-2.625)(-.25,13)
    \psframe[fillstyle=solid, fillcolor=myfill](-1,8)(1.75,7.75)
    \psframe[fillstyle=solid, fillcolor=myfill](-1,8.25)(-.75,7.5)
    \pscircle[fillstyle=solid, fillcolor=myfill](-.375,7.875){.2}
    \psframe[fillstyle=solid, fillcolor=myfill](1.5,8.15)(3,7.6)
    \psframe[fillstyle=solid, fillcolor=myfill](-1,4)(1.75,3.75)
    \psframe[fillstyle=solid, fillcolor=myfill](-1,4.25)(-.75,3.5)
    \pscircle[fillstyle=solid, fillcolor=myfill](-.375,3.875){.2}
    \psframe[fillstyle=solid, fillcolor=myfill](1.5,4.15)(3,3.6)
    % support elevateur
    \pspolygon[fillstyle=solid, fillcolor=myfill, linearc=.05](.25,-.25)(3.25,-1.25)(.25,-2.25)(1.25,-2.25)(4.25,-1.25)(1.25,-.25)
    \pspolygon[fillstyle=solid, fillcolor=myfill, linearc=.05](4.25,-.25)(1.25,-1.25)(4.25,-2.25)(3.25,-2.25)(.25,-1.25)(3.25,-.25)
    \psline(.25,-1.25)(4.5,-1.25)
    \psframe[fillstyle=solid, fillcolor=myfill](4.5,-1)(4.75,-1.5)
    \psframe[fillstyle=solid, fillcolor=myfill](0,0)(4.5,-.25)
    \psframe[fillstyle=solid, fillcolor=myfill](0,-2.25)(4.5,-2.5)
    % base
    \psframe[fillstyle=solid, fillcolor=myfill](-1,-2.5)(5,-2.75)
}

\begin{document}

\psset{unit=0.5cm}
\psgrid[subgriddiv=1, griddots=10, gridlabels=5pt, gridwidth=0.5pt](0,0)(20,20)
\pstBallon[refrigerantBoulles, glassType=ballon]

\pstClamp

\rput{0}(8,8){\pstClamp}

\end{document}