如何在自主模式下启用或绑定 Cisco 3502i AP 上的 80MHz 信道?

如何在自主模式下启用或绑定 Cisco 3502i AP 上的 80MHz 信道?

我有一个 Cisco AIR-CAP3502I-A-K9,使用 F/W ap3g1-k9w7-xx-153-3.JF5,处于自主模式。我尝试了所有能想到的方法(谷歌不是我的朋友)来配置 5GHz 无线电以使用 300MBps?我可以使用此 CLI 命令配置其他通道:

速度 6.0 9.0 12.0 18.0 24.0 36.0 48.0 54.0 m0. m1. m2. m3. m4. m5. m6. m7. m8. m9. m10. m11. m12. m13. m14. m15.

但我在速度测试中得到的最高速度约为 27 Mbps,使用 iPhone 7 plus,只有 2 个客户端连接到 AP。

我也关注了以下 Serverfault 页面,但也没有成功——是的,这是我发布的一篇文章,当时它“似乎”有效,但实际上并非如此: 在 Cisco 3502i 上启用 300Mbps 的正确方法是什么?

那么我遗漏了什么?

我的带有掩码字段的 AP 配置如下。

!
! Last configuration change at 17:59:43 -0700 Sun Jun 9 2019 by Cisco
! NVRAM config last updated at 17:59:47 -0700 Sun Jun 9 2019 by Cisco
! NVRAM config last updated at 17:59:47 -0700 Sun Jun 9 2019 by Cisco
version 15.3
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
service password-encryption
!
hostname ap
!
!
logging rate-limit console 9
enable secret XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX
!
no aaa new-model
clock timezone -0700 -7 0
no ip source-route
no ip cef
ip domain name XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX
!
!
!
!
dot11 pause-time 100
dot11 syslog
!
dot11 ssid 4ff0-58
   authentication open 
   authentication key-management wpa version 2
   guest-mode
   infrastructure-ssid
   wpa-psk ascii XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX
!
dot11 ssid 7ab0-24
   authentication open 
   authentication key-management wpa version 2
   guest-mode
   infrastructure-ssid
   wpa-psk ascii XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX
!
!
!
no ipv6 cef
!
!
username Cisco password XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX
!
!
bridge irb
!
!
!
interface Dot11Radio0
 no ip address
 !
 encryption mode ciphers aes-ccm 
 !
 ssid XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX
 !
 antenna gain 0
 speed  basic-11.0 6.0 9.0 12.0 18.0 24.0 36.0 48.0 54.0 m0. m1. m2. m3. m4. m5. m6. m7. m8. m9. m10. m11. m12. m13. m14. m15.
 channel 2462
 station-role root
 no dot11 extension aironet
 world-mode dot11d country-code US indoor
 bridge-group 1
 bridge-group 1 subscriber-loop-control
 bridge-group 1 spanning-disabled
 bridge-group 1 block-unknown-source
 no bridge-group 1 source-learning
 no bridge-group 1 unicast-flooding
!
interface Dot11Radio1
 no ip address
 !
 encryption mode ciphers aes-ccm 
 !
 ssid XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX
 !
 antenna gain 0
 peakdetect
 dfs band 3 block
 speed  basic-6.0 9.0 12.0 18.0 24.0 36.0 48.0 54.0 m0. m1. m2. m3. m4. m5. m6. m7. m8. m9. m10. m11. m12. m13. m14. m15.
 channel width 40-above
 channel 5180
 station-role root
 no dot11 extension aironet
 world-mode dot11d country-code US indoor
 bridge-group 1
 bridge-group 1 subscriber-loop-control
 bridge-group 1 spanning-disabled
 bridge-group 1 block-unknown-source
 no bridge-group 1 source-learning
 no bridge-group 1 unicast-flooding
!
interface GigabitEthernet0
 no ip address
 duplex auto
 speed auto
 bridge-group 1
 bridge-group 1 spanning-disabled
 no bridge-group 1 source-learning
!
interface BVI1
 mac-address 70ca.9b98.f5bf
 ip address dhcp client-id GigabitEthernet0
 ipv6 address dhcp
 ipv6 address autoconfig
!
ip forward-protocol nd
ip http server
no ip http secure-server
ip http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag
!
!
bridge 1 route ip
!
!
!
line con 0
line vty 0 4
 login local
 transport input all
!
sntp server 132.163.96.1
sntp broadcast client
end

答案1

接口Dot11Radio1
信道宽度40以上

您已将 5GHz 无线电配置为 40MHz 信道宽度。

通过速度测试获得的实际速度与无线 PHY 速度将有很大差异。

相关内容